- 您现在的位置：买卖IC网 > PDF目录9789 > AD9238BSTRL-40 (Analog Devices Inc)IC ADC 12BIT DUAL 40MSPS 64-LQFP PDF资料下载
参数资料
| 型号： | AD9238BSTRL-40 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/48页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT DUAL 40MSPS 64-LQFP |
| 产品变化通告： | AD9238 Lead Discontinuation 12/Sept/2011 |
| 标准包装： | 2,000 |
| 位数： | 12 |
| 采样率（每秒）： | 40M |
| 数据接口： | 并联 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 330mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（7x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极 |
| 配用： | AD9238BCP-65EBZ-ND - BOARD EVAL WITH AD9238BCP-65 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD9238
Rev. C | Page 19 of 48
DATA FORMAT
The AD9238 data output format can be configured for either
twos complement or offset binary. This is controlled by the data
format select pin (DFS). Connecting DFS to AGND produces
offset binary output data. Conversely, connecting DFS to AVDD
formats the output data as twos complement.
The output data from the dual ADCs can be multiplexed onto a
single 12-bit output bus. The multiplexing is accomplished by
toggling the MUX_SELECT bit, which directs channel data to
the same or opposite channel data port. When MUX_SELECT
is logic high, the Channel A data is directed to the Channel A
output bus, and the Channel B data is directed to the Channel B
output bus. When MUX_SELECT is logic low, the channel data
is reversed, that is the Channel A data is directed to the
Channel B output bus, and the Channel B data is directed to the
Channel A output bus. By toggling the MUX_SELECT bit,
multiplexed data is available on either of the output data ports.
If the ADCs run with synchronized timing, this same clock can
be applied to the MUX_SELECT pin. Any skew between CLK_A,
CLK_B, and MUX_SELECT can degrade ac performance. It is
recommended to keep the clock skew <100 pS. After the
MUX_SELECT rising edge, either data port has the data for its
respective channel; after the falling edge, the alternate channel’s
data is placed on the bus. Typically, the other unused bus would
be disabled by setting the appropriate OEB high to reduce
power consumption and noise. Figure 34 shows an example of
multiplex mode. When multiplexing data, the data rate is two
times the sample rate. Note that both channels must remain
active in this mode and that each channel’s power-down pin
must remain low.
VOLTAGE REFERENCE
A stable and accurate 0.5 V voltage reference is built into the
AD9238. The input range can be adjusted by varying the reference
voltage applied to the AD9238, using either the internal
reference with different external resistor configurations or an
externally applied reference voltage. The input span of the ADC
tracks reference voltage changes linearly. If the ADC is being
driven differentially through a transformer, the reference voltage
can be used to bias the center tap (common-mode voltage).
The shared reference mode allows the user to connect the references
from the dual ADCs together externally for superior gain and
offset matching performance. If the ADCs are to function
independently, the reference decoupling can be treated
independently and can provide superior isolation between the dual
channels. To enable shared reference mode, the SHARED_REF
pin must be tied high and the external differential references
must be externally shorted. (REFT_A must be externally
shorted to REFT_B, and REFB_A must be shorted to REFB_B.)
Internal Reference Connection
A comparator within the AD9238 detects the potential at the
SENSE pin and configures the reference into four possible states,
which are summarized in Table 7. If SENSE is grounded, the
reference amplifier switch is connected to the internal resistor
divider (see Figure 35), setting VREF to 1 V. Connecting the
SENSE pin to VREF switches the reference amplifier output to
the SENSE pin, completing the loop and providing a 0.5 V
reference output. If a resistor divider is connected, as shown in
Figure 36, the switch is again set to the SENSE pin. This puts
the reference amplifier in a noninverting mode with the VREF
output defined as
VREF = 0.5 × (1 + R2/R1)
In all reference configurations, REFT and REFB drive the ADC
core and establish its input span. The input range of the ADC
always equals twice the voltage at the reference pin for either an
internal or an external reference.
VIN+
VIN–
10
μF
10
μF
0.1
μF
0.1
μF
REFT
ADC
CORE
SELECT
LOGIC
SENSE
0.1
μF
0.5V
AD9238
REFB
0.1
μF
VREF
02640-034
Figure 35. Internal Reference Configuration
Table 7. Reference Configuration Summary
Selected Mode
SENSE Voltage
Resulting VREF (V)
Resulting Differential Span (V p-p)
External Reference
AVDD
N/A
2 × External Reference
Internal Fixed Reference
VREF
0.5
1.0
Programmable Reference
0.2 V to VREF
0.5 × (1 + R2/R1)
2 × VREF (See Figure 36)
Internal Fixed Reference
AGND to 0.2 V
1.0
2.0
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T25B29PA | CONN RCPT 29POS JAM NUT W/PINS |
| AD9235BRURL7-65 | IC ADC 12BIT 65MSPS 28-TSSOP |
| MS27497E16F35PA | CONN RCPT 55POS WALL MNT W/PINS |
| MAX3222EUP/V+ | TXRX RS-232 ESD PROTECT 20TSSOP |
| MS27473P14F37P | CONN PLUG 37POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9238BSTRL-65 | 功能描述:IC ADC 12BIT DUAL 65MSPS 64-LQFP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD9238BSTZ-20 | 功能描述:IC ADC 12BIT DUAL 20MSPS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD9238BSTZ-20EB | 制造商:AD 制造商全称:Analog Devices 功能描述:12-Bit, 20 MSPS/40 MSPS/65 MSPS Dual A/D Converter |
| AD9238BSTZ-40 | 功能描述:IC ADC 12BIT DUAL 40MSPS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD9238BSTZ-40 | 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
发布紧急采购，3分钟左右您将得到回复。