- 您现在的位置：买卖IC网 > PDF目录9502 > AD9273BSVZ-40 (Analog Devices Inc)IC ADC OCT 12BIT 40MSPS 100-TQFP PDF资料下载
参数资料
| 型号： | AD9273BSVZ-40 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/48页 |
| 文件大小： | 0K |
| 描述： | IC ADC OCT 12BIT 40MSPS 100-TQFP |
| 标准包装： | 1 |
| 类型： | AAF，ADC，交叉点开关，LNA，VGA |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 40M |
| 数据接口： | 串行，SPI? |
| 电压电源： | 模拟和数字 |
| 电源电压： | 1.8V，3V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP 裸露焊盘 |
| 供应商设备封装： | 100-TQFP-EP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD9273
Rev. B | Page 25 of 48
INPUT OVERDRIVE
CW DOPPLER OPERATION
Excellent overload behavior is of primary importance in
ultrasound. Both the LNA and VGA have built-in overdrive
protection and quickly recover after an overload event.
Modern ultrasound machines used for medical applications
employ a 2N binary array of receivers for beam forming, with
typical array sizes of 16 or 32 receiver channels phase-shifted
and summed together to extract coherent information. When
used in multiples, the desired signals from each channel can be
summed to yield a larger signal (increased by a factor N, where
N is the number of channels), and the noise is increased by the
square root of the number of channels. This technique enhances
the signal-to-noise performance of the machine. The critical
elements in a beam-former design are the means to align the
incoming signals in the time domain and the means to sum the
individual signals into a composite whole.
Input Overload Protection
As with any amplifier, voltage clamping prior to the inputs is
highly recommended if the application is subject to high
transient voltages.
In Figure 44, a simplified ultrasound transducer interface is
shown. A common transducer element serves the dual functions
of transmitting and receiving ultrasound energy. During the
transmitting phase, high voltage pulses are applied to the ceramic
elements. A typical transmit/receive (T/R) switch can consist of
four high voltage diodes in a bridge configuration. Although the
diodes ideally block transmit pulses from the sensitive receiver
input, diode characteristics are not ideal, and the resulting leakage
transients imposed on the LI-x inputs can be problematic.
Beam forming, as applied to medical ultrasound, is defined as the
phase alignment and summation of signals that are generated
from a common source but received at different times by a
multielement ultrasound transducer. Beam forming has two
functions: it imparts directivity to the transducer, enhancing its
gain, and it defines a focal point within the body from which the
location of the returning echo is derived.
Because ultrasound is a pulse system and time-of-flight is used to
determine depth, quick recovery from input overloads is essential.
Overload can occur in the preamp and the VGA. Immediately
following a transmit pulse, the typical VGA gains are low, and
the LNA is subject to overload from T/R switch leakage. With
increasing gain, the VGA can become overloaded due to strong
echoes that occur near field echoes and acoustically dense materials,
such as bone.
The AD9273 includes the front-end components needed to
implement analog beam forming for CW Doppler operation.
These components allow CW channels with similar phases to be
coherently combined before phase alignment and down mixing,
thus reducing the number of delay lines or adjustable phase shifters/
are used, the phase alignment is performed, and then the channels
are coherently summed and down converted by a dynamic range
I/Q demodulator. Alternatively, if phase shifters/down mixers,
and downconversion are done before coherently summing all
channels into I/Q signals. In either case, the resultant I and Q
signals are filtered and sampled by two high resolution ADCs,
and the sampled signals are processed to extract the relevant
Doppler information.
Figure 44 illustrates an external overload protection scheme. A
pair of back-to-back signal diodes is installed prior to installing the
ac-coupling capacitors. Keep in mind that all diodes shown in
this example are prone to exhibiting some amount of shot noise.
Many types of diodes are available for achieving the desired noise
performance. The configuration shown in Figure 44 tends to add
2 nV/√Hz of input-referred noise. Decreasing the 5 kΩ resistor
and increasing the 2 kΩ resistor may improve noise contribution,
depending on the application. With the diodes shown in Figure 44,
clamping levels of ±0.5 V or less significantly enhance the overload
performance of the system.
Alternately, the LNA of the AD9273 can directly drive the AD8333
or AD8339 without the crosspoint switch. The LO-x pins present
the inverting LNA output, and the LOSW-x pins can be configured
via Register 0x2C (see Table 17) to connect to the noninverting
output to provide a differential output of the LNA. The LNA output
full-scale voltage of the AD9273 is 4.4 V p-p, and the input full-
scale voltage is 2.7 V p-p. If no attenuation is provided between
the LNA output and the demodulator, the LNA input full-scale
voltage must be limited.
TRANSDUCER
10nF
2k
5k
5k
AD9273
Tx
DRIVER
HV
+5V
–5V
LNA
07
03
0-
10
0
Figure 44. Input Overload Protection
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BTM-MY-S | CONVERTER MOD DC/DC 10V 50W |
| VE-B3K-IU | CONVERTER MOD DC/DC 40V 200W |
| AD7581CQ | IC ADC DAS 8BIT 8CH 28CDIP |
| VI-BT1-MY-S | CONVERTER MOD DC/DC 12V 50W |
| VE-B3J-IU | CONVERTER MOD DC/DC 36V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9273BSVZ-50 | 功能描述:IC ADC ASD OCTAL 50MSPS 100-TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD9273BSVZRL-25 | 功能描述:模数转换器 - ADC 12Bit 25 MSPS Octal ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9273BSVZRL-40 | 功能描述:模数转换器 - ADC 12Bit 40 MSPS Octal ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9273BSVZRL-50 | 功能描述:模数转换器 - ADC 12Bit 50 MSPS Octal ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9273XBCZ | 功能描述:IC ADC 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。