参数资料
| 型号： | AD9283BRS-50 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT 50MSPS 3V 20-SSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 66 |
| 位数： | 8 |
| 采样率（每秒）： | 50M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 100mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，双极；2 个差分，双极 |
AD9283
–8–
REV. C
CODE
2.0
LS
B
–0.5
–1.0
–1.5
–2.0
0.5
0.0
1.0
1.5
TPC 13. Integral Nonlinearity
APPLICATIONS
Theory of Operation
The analog signal is applied differentially or single-endedly to
the inputs of the AD9283. The signal is buffered and fed for-
ward to an on-chip sample-and-hold circuit. The ADC core
architecture is a bit-per-stage pipeline type converter utilizing
switch capacitor techniques. The bit-per-stage blocks determine
the 5 MSBs and drive a FLASH converter to encode the 3 LSBs.
Each of the 5 MSB stages provides sufficient overlap and error
correction to allow optimization of performance with respect to
comparator accuracy. The output staging block aligns the data,
carries out the error correction and feeds the data to the eight
output buffers. The AD9283 includes an on-chip reference
(nominally 1.25 V) and generates all clocking signals from one
externally applied encode command. This makes the ADC easy
to interface with and requires very few external components for
operation.
ENCODE Input
The ENCODE input is fully TTL/CMOS compatible with a
nominal threshold of 1.5 V. Care was taken on the chip to
match clock line delays and maintain sharp clock logic transi-
tions. Any high speed A/D converter is extremely sensitive to
the quality of the sampling clock provided by the user. This
ADC uses an on-chip sample-and-hold circuit which is essen-
tially a mixer. Any timing jitter on the ENCODE will be com-
bined with the desired signal and degrade the high frequency
performance of the ADC. The user is advised to give commen-
surate thought to the clock source.
Analog Input
The analog input to the ADC is fully differential and both inputs
are internally biased. This allows the most flexible use of ac or dc
and differential or single-ended input modes. For peak performance
the inputs are biased at 0.3
× VD. See the specification table for
allowable common-mode range when dc coupling the input.
The inputs are also buffered to reduce the load the user needs to
drive. For best dynamic performance, the impedances at AIN and
AIN should be matched. The importance of this increases with
sampling rate and analog input frequency. The nominal input
range is 1.024 V p-p.
Digital Outputs
The digital outputs are TTL/CMOS compatible. The output
buffers are powered from a separate supply, allowing adjustment
of the output voltage swing to ease interfacing with 2.5 V or
3.3 V logic. The AD9283 goes into a low power state within two
clock cycles following the assertion of the PWRDWN input.
PWRDWN is asserted with a logic high. During power-down
the outputs transition to a high impedance state. The time it
takes to achieve optimal performance after disabling the power-
down mode is approximately 15 clock cycles. Care should be
taken when loading the digital outputs of any high speed ADC.
Large output loads create current transients on the chip that can
degrade the converter’s performance.
Voltage Reference
A stable and accurate 1.25 V voltage reference is built into the
AD9283 (VREF OUT). In normal operation, the internal refer-
ence is used by strapping Pins 2 and 3 of the AD9283 together.
The input range can be adjusted by varying the reference volt-
age applied to the AD9283. No degradation in performance
occurs when the reference is adjusted
±5%. The full-scale range
of the ADC tracks reference voltage changes linearly. Whether
used or not, the internal reference (Pin 2) should be bypassed
with a 0.1
F capacitor to ground.
Timing
The AD9283 provides latched data outputs with four pipeline
delays. Data outputs are available one propagation delay (tPD)
after the rising edge of the encode command (Figure 1. Timing
Diagram). The minimum guaranteed conversion rate to the
ADC is 1 MSPS. The dynamic performance of the converter
will degrade at encode rates below this sample rate.
Evaluation Board
The AD9283 evaluation board offers an easy way to test the
AD9283. It only requires a 3 V supply, an analog input and
encode clock to test the AD9283. The board is shipped with the
100 MSPS grade ADC.
The analog input to the board accepts a 1 V p-p signal centered
at ground. J1 should be used (Jump E3–E4, E18–E19) to drive
the ADC through Transformer T1. J2 should be used for single-
ended input drive (Jump E19–E21).
Both J1 and J2 are terminated to 50
on the PCB. Each analog
path is ac-coupled to an on-chip resistor divider which provides
the required dc bias.
A (TTL/CMOS Level) sample clock is applied to connector
J3 which is terminated through 50
on the PCB. This clock is
buffered by U5 which also provides the clocks for the 574
latches, DAC, and the off-card latch clock CLKCON. (Timing
can be modified at E17.)
There is a reconstruction DAC (AD9760) on the PCB. The
DAC is on the board to assist in debug only—the outputs
should not be used to measure performance of the ADC.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9283BRS-100 | IC ADC 8BIT 100MSPS 3V 20-SSOP |
| MAX223CWI+T | IC RS-232 DRVR/RCVR 28-SOIC |
| D38999/24MC4PA | CONN RCPT 4POS JAM NUT W/PINS |
| MAX200CWP+T | IC TXRX RS-232 W/CAP 20-SOIC |
| MAX3443ECPA+ | IC TXRX RS-485 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9283BRS-50Z | 制造商:Analog Devices 功能描述:ADC 8BIT 50MSPS 0.75LSB 20SSOP 制造商:Analog Devices 功能描述:ADC, 8BIT, 50MSPS, 0.75LSB, 20SSOP 制造商:Analog Devices 功能描述:ADC, 8BIT, 50MSPS, 0.75LSB, 20SSOP, Resolution (Bits):8bit, Sampling Rate:50MSPS, Supply Voltage Type:Single, Supply Voltage Min:2.7V, Supply Voltage Max:3.6V, Digital IC Case Style:SSOP, No. of Pins:20, Input Channel , RoHS Compliant: Yes |
| AD9283BRS-80 | 功能描述:IC ADC 8BIT 80MSPS 3V 20-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD9283BRS-RL100 | 功能描述:IC ADC 8BIT 100MSPS 3V 20-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD9283BRS-RL50 | 功能描述:IC ADC 8BIT 50MSPS 3V 20-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD9283BRS-RL80 | 制造商:Analog Devices 功能描述:ADC Single Pipelined 80Msps 8-bit Parallel 20-Pin SSOP T/R |
发布紧急采购，3分钟左右您将得到回复。