- 您现在的位置：买卖IC网 > PDF目录10518 > AD9432BSVZ-105 (Analog Devices Inc)IC ADC 12BIT 105MSPS 52TQFP PDF资料下载
参数资料
| 型号： | AD9432BSVZ-105 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 105MSPS 52TQFP |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 105M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.1W |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-TQFP 裸露焊盘 |
| 供应商设备封装： | 52-TQFP-EP（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个单端，单极；2 个差分，单极 |
AD9432
Rev. F | Page 13 of 16
THEORY OF OPERATION
The AD9432 is a 12-bit pipeline converter that uses a switched-
capacitor architecture. Optimized for high speed, this converter
provides flat dynamic performance up to frequencies near
Nyquist. DNL transitional errors are calibrated at final test to
a typical accuracy of 0.25 LSB or less.
ANALOG INPUT
The analog input to the AD9432 is a differential buffer. The
input buffer is self-biased by an on-chip resistor divider that
sets the dc common-mode voltage to a nominal 3 V (see the
Equivalent Circuits section). Rated performance is achieved
by driving the input differentially. The minimum input offset
voltage is obtained when driving from a source with a low
differential source impedance, such as a transformer in ac
applications. Capacitive coupling at the inputs increases the
input offset voltage by as much as ±25 mV. Driving the ADC
single-ended degrades performance. For best dynamic perfor-
mance, impedances at AIN and AIN should match.
Special care was taken in the design of the analog input section
of the AD9432 to prevent damage and corruption of data when
the input is overdriven. The nominal input range is 2 V p-p.
Each analog input is 1 V p-p when driven differentially.
00
58
7-
02
5
4.0
3.5
2.5
3.0
2.0
AIN
Figure 26. Full-Scale Analog Input Range
ENCODE INPUT
Any high speed ADC is extremely sensitive to the quality of the
sampling clock provided by the user. A track-and-hold circuit is
essentially a mixer, and any noise, distortion, or timing jitter on
the clock is combined with the desired signal at the ADC output.
For this reason, considerable care has been taken in the design
of the encode input of the AD9432, and the user is advised to
give commensurate thought to the clock source. The encode
input supports differential or single-ended mode and is fully
TTL-/CMOS-compatible.
Note that the encode inputs cannot be driven directly from PECL
level signals (VIHD is 3.5 V maximum). PECL level signals can
easily be accommodated by ac coupling, as shown in Figure 27.
Good performance is obtained using an MC10EL16 translator
in the circuit to drive the encode inputs.
00
58
7-
02
6
PECL
GATE
ENCODE
AD9432
ENCODE
510
0.1F
510
Figure 27. AC Coupling to Encode Inputs
ENCODE VOLTAGE LEVEL DEFINITION
The voltage level definitions for driving ENCODE and ENCODE
in single-ended and differential mode are shown in
.
0
05
87
-02
7
VIHD
VICM
VID
VILD
ENCODE
VIHS
VILS
ENCODE
0.1F
Figure 28. Differential and Single-Ended Input Levels
Table 5. Encode Inputs
Input
Min
Nominal
Max
Differential Signal Amplitude (VID)
500 mV
750 mV
High Differential Input Voltage (VIHD)
3.5 V
Low Differential Input Voltage (VILD)
0 V
Common-Mode Input (VICM)
1.25 V
1.6 V
High Single-Ended Voltage (VIHS)
2 V
3.5 V
Low Single-Ended Voltage (VILS)
0 V
0.8 V
Often, the cleanest clock source is a crystal oscillator producing a
pure sine wave. In this configuration, or with any roughly symmet-
rical clock input, the input can be ac-coupled and biased to a
reference voltage that also provides the encode. This ensures
that the reference voltage is centered on the encode signal.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B0X-MX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-B4P-IV-F4 | CONVERTER MOD DC/DC 13.8V 150W |
| AD9432BSTZ-105 | IC ADC 12BIT 105MSPS 52-LQFP |
| UP050B681K-A-B | CAP CER 680PF 50V 10% AXIAL |
| LTC1605AIG#PBF | IC A/D CONV 16BIT SAMPLNG 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9432BSVZ-1051 | 制造商:AD 制造商全称:Analog Devices 功能描述:12-Bit, 80 MSPS/105 MSPS ADC |
| AD9432BSVZ-80 | 功能描述:IC ADC 12BIT 80MSPS 52TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD9432BSVZ-801 | 制造商:AD 制造商全称:Analog Devices 功能描述:12-Bit, 80 MSPS/105 MSPS ADC |
| AD9432PCB | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed ADC USB FIFO Evaluation Kit |
| AD9433 | 制造商:AD 制造商全称:Analog Devices 功能描述:12-Bit, 105 MSPS/125 MSPS IF Sampling A/D Converter |
发布紧急采购，3分钟左右您将得到回复。