参数资料
| 型号： | AD9632AR |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF ULDIST 70MA 8SOIC |
| 标准包装： | 1 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 1500 V/µs |
| -3db带宽： | 250MHz |
| 电流 - 输入偏压： | 2µA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 16mA |
| 电流 - 输出 / 通道： | 70mA |
| 电压 - 电源，单路/双路(±)： | 6 V ~ 12 V，±3 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
AD9631/AD9632
Data Sheet
Rev. D | Page 18 of 20
ANALOG-TO-DIGITAL CONVERTER (ADC) DRIVER
As ADCs move toward higher speeds with higher resolutions,
there becomes a need for high performance drivers that will not
degrade the analog signal to the converter. It is desirable from a
system’s standpoint that the ADC be the element in the signal
chain that ultimately limits overall distortion. Figure 66 is such
an example.
Figure 66. AD9631 Used as Driver for an ADC Signal Chain
LAYOUT CONSIDERATIONS
requires careful attention to board layout and component
selection. Proper RF design techniques and low-pass parasitic
component selection are mandatory.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance path. Remove the ground plane from the area near
the input pins to reduce stray capacitance.
Use chip capacitors for supply bypassing (see Figure 59 and
Figure 60). Connect one end to the ground plane, and the other
within 1/8 inch of each power pin. Connect an additional large
(0.47 μF to 10 μF) tantalum electrolytic capacitor in parallel,
though not necessarily so close, to supply current for fast, large
signal changes at the output.
The feedback resistor should be located close to the inverting
input pin to keep the stray capacitance at this node to a mini-
mum. Capacitance variations of less than 1 pF at the inverting
input will significantly affect high speed performance.
Use stripline design techniques for long signal traces (greater
than about 1 inch). These should be designed with a
characteristic impedance of 50 Ω or 75 Ω and be properly
terminated at each end.
00601-
066
+5V
–5V
130
140
ANALOG IN
AD9631
ADC
相关PDF资料 |
PDF描述 |
|---|---|
| LT2179IS#TRPBF | IC OPAMP MICROPOWER QUAD 14SOIC |
| RNCP0805FTD8K25 | RES 8.25K OHM 1/4W 1% 0805 SMD |
| AD8036AN | IC OPAMP VF ULDIST LN 70MA 8DIP |
| AD8036AR | IC OPAMP VF ULDIST LN 70MA 8SOIC |
| AD848AQ | IC OPAMP GP 175MHZ LP 32MA 8CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9632AR-EBZ | 功能描述:BOARD EVAL FOR AD9632AR RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD9632AR-REEL | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk ±6V 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:WIDE BW, GAIN=2 OP AMP - Tape and Reel |
| AD9632AR-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk 制造商:Analog Devices 功能描述:IC OP-AMP HIGH SPEED |
| AD9632ARZ | 功能描述:IC OPAMP VF ULDIST 70MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD9632ARZ | 制造商:Analog Devices 功能描述:OP-AMP, VOLTAGE FEEDBACK, 250MHZ, 1500V/ |
发布紧急采购，3分钟左右您将得到回复。