- 您现在的位置：买卖IC网 > PDF目录6110 > ADA4062-2ACPZ-R7 (Analog Devices Inc)IC OPAMP JFET 1.4MHZ DL 10LFCSP PDF资料下载
参数资料
| 型号： | ADA4062-2ACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP JFET 1.4MHZ DL 10LFCSP |
| 设计资源： | 8-Pole Active Low-Pass Filter Optimized for Precision, Low Noise, and High Gain Using AD8622 and ADA4062-2 (CN0127) |
| 标准包装： | 1 |
| 放大器类型： | J-FET |
| 电路数： | 2 |
| 转换速率： | 3.3 V/µs |
| 增益带宽积： | 1.4MHz |
| 电流 - 输入偏压： | 2pA |
| 电压 - 输入偏移： | 750µV |
| 电流 - 电源： | 165µA |
| 电流 - 输出 / 通道： | 20mA |
| 电压 - 电源，单路/双路(±)： | 8 V ~ 36 V，±4 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFQFN，CSP |
| 供应商设备封装： | 10-LFCSP-UQ（1.6x1.3） |
| 包装： | 标准包装 |
| 其它名称： | ADA4062-2ACPZ-R7DKR |
ADA4062-2/ADA4062-4
Rev. B | Page 15 of 20
APPLICATIONS INFORMATION
NOTCH FILTER
A notch filter rejects a specific interfering frequency and can be
implemented using a single op amp. Figure 59 shows a 60 Hz
notch filter that uses the twin-T network with the ADA4062-x
configured as a voltage follower. The ADA4062-x works as a buffer
that provides high input resistance and low output impedance.
The low bias current (2 pA typical) and high input resistance
(10 TΩ typical) of the ADA4062-x enable large resistors and small
capacitors to be used.
Alternatively, different combinations of resistor and capacitor
values can be used to achieve the desired notch frequency.
However, the major drawback to this circuit topology is the
need to ensure that all the resistors and capacitors be closely
matched. If they are not closely matched, the notch frequency
offset and drift cause the circuit to attenuate at a frequency
other than the ideal notch frequency.
Therefore, to achieve the desired performance, 1% or better
component tolerances are usually required. In addition, a notch
filter requires an op amp with a bandwidth of at least 100× to
200× the center frequency. Hence, using the ADA4062-x with
a bandwidth of 1.4 MHz is excellent for a 60 Hz notch filter.
Figure 60 shows the frequency response of the notch filter. At
60 Hz, the notch filter has about 50 dB attenuation of signal.
+VSY
–VSY
IN
VO
fO =
R1 = R2 = 2R3
C1 = C2 =
07
67
0-
06
0
R1
804k
R2
804k
R3
402k
C3
6.6nF
C2
3.3nF
C3
2
C1
3.3nF
ADA4062-x
1
2π R1 C1
Figure 59. Notch Filter Circuit
07
67
0
-05
7
FREQUENCY (Hz)
GA
IN
(
d
B
)
20
10
0
–10
–30
–20
–40
–50
–60
–70
–80
10
100
1k
Figure 60. Frequency Response of the Notch Filter
HIGH-SIDE SIGNAL CONDITIONING
Many applications require the sensing of signals near the positive
rail. The ADA4062-x can be used in high-side current sensing
applications. Figure 61 shows a high-side signal conditioning
circuit using the ADA4062-x. The ADA4062-x has an input
common-mode range that includes the positive supply (11.5 V ≤
VCM ≤ +15 V). In the circuit, the voltage drop across a low value
resistor, such as the 0.1 Ω shown in Figure 61, is amplified by a
factor of 5 using the ADA4062-x.
ADA4062-x
+15V
–15V
100k
0.1
100k
500k
VO
RL
07
67
0-
0
58
Figure 61. High-Side Signal Conditioning
MICROPOWER INSTRUMENTATION AMPLIFIER
The ADA4062-2 is a dual amplifier and is perfectly suited for
applications that require lower supply currents. For supply
voltages of ±15 V, the supply current per amplifier is 165 μA
typical. The ADA4062-2 also offers a typical low offset voltage
drift of 5 μV/°C and a very low bias current of 2 pA, which
make it well suited for instrumentation amplifiers.
Figure 62 shows the classic 2-op-amp instrumentation amplifier
with four resistors using the ADA4062-2. The key to high CMRR
for this instrumentation amplifier are resistors that are well
matched to both the resistive ratio and relative drift. For true
difference amplification, matching of the resistor ratio is very
important, where R3/R4 = R1/R2. Assuming perfectly matched
resistors, the gain of the circuit is 1 + R2/R1, which is approximately
100. Tighter matching of two op amps in one package, as is the
case with the ADA4062-2, offers a significant boost in performance
over the classical 3-op-amp configuration. Overall, the circuit only
requires about 330 μA of supply current.
R3
10.1k
R4
1M
+15V
1/2
–15V
V1
R2
1M
+15V
–15V
V2
R1
10.1k
ADA4062-2
VO
VO = 100(V2 – V1)
TYPICAL: 0.5mV < │V2 – V1│< 135mV
TYPICAL: –13.8V < VO < +13.5V
USE MATCHED RESISTORS
07
67
0-
0
59
1/2
Figure 62. Micropower Instrumentation Amplifier
相关PDF资料 |
PDF描述 |
|---|---|
| 0072.4841.B1 | AVTT VARISTOR 480VAC 10MM THT |
| 0072.4641.B1 | AVTT VARISTOR 460VAC 10MM THT |
| 0071.3261.B1 | AVTP VARISTOR 320VAC 14MM THT |
| 0071.3061.B1 | AVTP VARISTOR 300VAC 14MM THT |
| 0071.2761.B1 | AVTP VARISTOR 270VAC 14MM THT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4062-2ACPZ-RL | 功能描述:IC OPAMP JFET 1.4MHZ DL 10LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
| ADA4062-2ARMZ | 功能描述:IC OPAMP JFET 1.4MHZ DUAL 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| ADA4062-2ARMZ-R7 | 功能描述:IC AMP DUAL LP JFET 18V 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
| ADA4062-2ARMZ-RL | 功能描述:IC OPAMP JFET 1.4MHZ DUAL 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
| ADA4062-2ARZ | 功能描述:IC OPAMP JFET 1.4MHZ DUAL 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。