- 您现在的位置：买卖IC网 > PDF目录10605 > ADA4420-6ARQZ-RL (Analog Devices Inc)IC FILTER VIDEO 6CH HD/SD 16QSOP PDF资料下载
参数资料
| 型号： | ADA4420-6ARQZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC FILTER VIDEO 6CH HD/SD 16QSOP |
| 标准包装： | 2,500 |
| 类型： | 视频滤波器 |
| 应用： | DVD，HD，机顶盒，录音机 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
ADA4420-6
Rev. A | Page 11 of 16
APPLICATIONS INFORMATION
OVERVIEW
With its high impedance inputs and high output drive, the
ADA4420-6 is ideally suited to video reconstruction and anti-
alias filtering applications. The high impedance inputs give
designers flexibility with regard to how the input signals are
terminated. Devices with DAC current source outputs that feed
the ADA4420-6 can be loaded in whatever resistance provides
the best performance, and devices with voltage outputs can be
optimally terminated as well. The ADA4420-6 outputs can each
drive up to two source-terminated, 75 Ω loads and; therefore, can
directly drive the outputs from set-top boxes and DVDs without
the need for a separate output buffer.
DISABLE
The ADA4420-6 includes a disable feature that can be used to
save power when a particular device is not in use. When disabled,
the ADA4420-6 typically draws only 7 μA from the supply. The
disable feature is asserted by pulling the DIS pin low.
Table 6 summarizes the operation of the disable feature.
Table 6. Disable Function
DIS Pin Connection
Status
VCC or Floating
Enabled
GND
Disabled
INPUT AND OUTPUT COUPLING
Inputs to the ADA4420-6 can be ac- or dc-coupled. For dc-coupled
inputs, the signal must be completely contained within the input
range of 0 V to 2.1 V. When using ac-coupled inputs, the lowest
point of the signal is clamped to approximately 0 V. The ADA4420-6
outputs can be either ac- or dc-coupled.
When driving single ac-coupled loads in standard 75 Ω video
distribution systems, a minimum capacitance of 220 μF is
recommended to avoid line and field droop. There are two ac
coupling options when driving two loads from one output. One
option simply uses the same value capacitor on the second load,
while the other option uses a common coupling capacitor that
is at least twice the value used for the single load (see Figure 21
and Figure 22).
When driving two parallel 150 Ω loads (75 Ω effective load), the
3 dB bandwidth of the filters typically varies from that of the filters
with a single 150 Ω load (see Figure 5).
75
CABLE
75
CABLE
220F
ADA4420-6
220F
75
0
75
32
-0
22
Figure 21. Driving Two AC-Coupled Loads with Two Coupling Capacitors
ADA4420-6
75
CABLE
75
CABLE
75
470F
0
75
32
-0
23
Figure 22. Driving Two AC-Coupled Loads with One Common Coupling Capacitor
PRINTED CIRCUIT BOARD (PCB) LAYOUT
As with all high speed applications, attention to the PCB layout
is of paramount importance. When designing with the ADA4420-6,
adhere to standard high speed layout practices. A solid ground
plane is recommended, and surface-mount, ceramic power supply
decoupling capacitors should be placed as close as possible to the
supply pins. Connect all of the ADA4420-6 GND pins to the
ground plane with traces that are as short as possible. Controlled
impedance traces of the shortest length possible should be used
to connect to the signal I/O pins and should not pass over any
voids in the ground plane. A 75 Ω impedance level is typically
used in video applications. When driving transmission lines,
include series termination resistors on the signal outputs of the
ADA4420-6.
When the ADA4420-6 receives its inputs from a device with
current outputs, the required load resistor value for the output
current is often different from the characteristic impedance of
the signal traces. In this case, if the interconnections are short
(<< 0.1 wavelength), the trace does not have to be terminated in
its characteristic impedance. Traces of 75 Ω can be used in this
instance, provided their lengths are an inch or two at most. This
is easily achieved because the ADA4420-6 and the device feeding it
are usually adjacent to each other, and connections can be made
that are less than one inch in length.
VIDEO ENCODER RECONSTRUCTION FILTER
The ADA4420-6 is easily applied as a reconstruction filter at the
DAC outputs of a video encoder. Figure 23 illustrates how to use
the ADA4420-6 in this type of application following an ADV734x
series video encoder, with a single-supply and ac-coupled outputs.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1480AEPI+ | IC INTERFACE RS485/RS422 28-DIP |
| MAX1490BEPG+ | IC RS485/RS422 DATA INTRFC 24DIP |
| MAX1480BEPI+ | IC RS485/RS422 DATA INTRFC 28DIP |
| DS2148T+ | IC LIU E1/T1/J1 5V 44-TQFP |
| MAX3800UHJ+ | IC EQUALIZER DRVR 3.2GBPS 32TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4420-6ARQZ-RL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost 6-Channel HD/SD Video Filter |
| ADA4420-6ARUZ | 制造商:Analog Devices 功能描述: |
| ADA4420-6ARUZ-R7 | 制造商:Analog Devices 功能描述: |
| ADA4420-6ARUZ-RL | 功能描述:IC FILTR VID6CH SD/ED/HD 38TSSOP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:上次购买时间 类型:视频滤波器 应用:DVD，HD，机顶盒，录音机 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:20-TSSOP 标准包装:1 |
| ADA4424 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel SD/ED/HD Video Filter with Charge Pump |
发布紧急采购，3分钟左右您将得到回复。