- 您现在的位置：买卖IC网 > PDF目录8548 > ADA4853-2YCPZ-RL (Analog Devices Inc)IC OPAMP VIDEO DUAL 16-LFCSP PDF资料下载
参数资料
| 型号： | ADA4853-2YCPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/21页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VIDEO DUAL 16-LFCSP |
| 设计资源： | Low Cost Video Multiplexer for Video Switching Using ADA4853-2 Op Amp with Disable Function (CN0076) |
| 标准包装： | 5,000 |
| 应用： | 电压反馈 |
| 输出类型： | 满摆幅 |
| 电路数： | 2 |
| -3db带宽： | 100MHz |
| 转换速率： | 120 V/µs |
| 电流 - 电源： | 1.4mA |
| 电流 - 输出 / 通道： | 160mA |
| 电压 - 电源，单路/双路(±)： | 2.65 V ~ 5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-VQ EP（3x3） |
| 包装： | 带卷 (TR) |
ADA4853-1/ADA4853-2/ADA4853-3
Rev. F | Page 16 of 20
CIRCUIT DESCRIPTION
The ADA4853-1/ADA4853-2/ADA4853-3 feature a high slew
rate input stage that is a true single-supply topology capable of
sensing signals at or below the minus supply rail. The rail-to-
rail output stage can pull within 100 mV of either supply rail
when driving light loads and within 200 mV when driving
150 . High speed performance is maintained at supply
voltages as low as 2.65 V.
HEADROOM CONSIDERATIONS
The ADA4853-1/ADA4853-2/ADA4853-3 are designed for use
in low voltage systems. To obtain optimum performance, it is
useful to understand the behavior of the amplifiers as input and
output signals approach their headroom limits. The input
common-mode voltage range of the amplifier extends from the
negative supply voltage (actually 200 mV below this) to within
1.2 V of the positive supply voltage.
Exceeding the headroom limits is not a concern for any
inverting gain on any supply voltage, as long as the reference
voltage at the positive input of the amplifier lies within the a
input common-mode range of the amplifier.
The input stage is the headroom limit for signals approaching
the positive rail. Figure 50 shows a typical offset voltage vs. the
input common-mode voltage for the ADA4853-1/ADA4853-2/
ADA4853-3 on a 5 V supply. Accurate dc performance is
maintained from approximately 200 mV below the negative
supply to within 1.2 V of the positive supply. For high speed
signals, however, there are other considerations. As the
common-mode voltage gets within 1.2 V of positive supply, the
amplifier responds well but the bandwidth begins to drop as the
common-mode voltage approaches the positive supply. This can
manifest itself in increased distortion or settling time. Higher
frequency signals require more headroom than the lower
frequencies to maintain distortion performance.
–0.6
–0.8
–1.0
–1.2
–1.4
–1.6
–1.8
–2.0
–1.0 –0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VCM (V)
V
OS
(m
V)
05884-
022
VS = 5V
Figure 50. VOS vs. Common-Mode Voltage, VS = 5 V
For signals approaching the negative supply, inverting gain, and
high positive gain configurations, the headroom limit is the
output stage. The ADA4853-1/ADA4853-2/ADA4853-3 use a
common-emitter output stage. This output stage maximizes the
available output range, limited by the saturation voltage of the
output transistors. The saturation voltage increases with the
drive current that the output transistor is required to supply due
to the collector resistance of the output transistor.
As the saturation point of the output stage is approached, the
output signal shows increasing amounts of compression and
clipping. For the input headroom case, higher frequency signals
require a bit more headroom than the lower frequency signals.
Figure 27 illustrates this point by plotting the typical distortion
vs. the output amplitude.
OVERLOAD BEHAVIOR AND RECOVERY
Input
The specified input common-mode voltage of the ADA4853-1/
ADA4853-2/ADA4853-3 is 200 mV below the negative supply
to within 1.2 V of the positive supply. Exceeding the top limit
results in lower bandwidth and increased rise time. Pushing the
input voltage of a unity-gain follower to less than 1.2 V from the
positive supply leads to an increasing amount of output error as
well as increased settling time. The recovery time from input
voltages 1.2 V or closer to the positive supply is approximately
40 ns; this is limited by the settling artifacts caused by transis-
tors in the input stage coming out of saturation.
The amplifiers do not exhibit phase reversal, even for input
voltages beyond the voltage supply rails. Going more than 0.6 V
beyond the power supplies turns on protection diodes at the
input stage, greatly increasing the current draw of the devices.
相关PDF资料 |
PDF描述 |
|---|---|
| LT6559CUD#TRPBF | IC AMP VIDEO TRPL 16-QFN |
| ADD8504WRUZ-REEL7 | IC GAMMA BUFFER LCD 4CH 16-TSSOP |
| VI-J4B-MW-S | CONVERTER MOD DC/DC 95V 100W |
| VI-BTX-MX-S | CONVERTER MOD DC/DC 5.2V 75W |
| VI-BTW-MX-S | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4853-2YCPZ-RL7 | 功能描述:IC OPAMP VIDEO DUAL 16-LFCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ADA4853-3 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Rail-to-Rail Output, Video Op Amps with Ultralow Power |
| ADA4853-3WYCPZ-R7 | 功能描述:IC OPAMP VIDEO TRIPLE 16LFCSP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 应用:电压反馈 输出类型:满摆幅 电路数:3 -3db 带宽:100MHz 压摆率:120 V/μs 电流 - 电源:1.4mA 电流 - 输出/通道:160mA 电压 - 电源，单/双（±）:2.65 V ~ 5 V 安装类型:表面贴装 封装/外壳:16-WFQFN 裸露焊盘，CSP 供应商器件封装:16-LFCSP-WQ（3x3） 标准包装:1,500 |
| ADA4853-3YCPZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Triple GP R-R O/P 5V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:OP AMP TRIPLE GP R-R O/P 5V 16LFCSP - Tape and Reel |
| ADA4853-3YCPZ-R7 | 功能描述:IC OPAMP VIDEO TRIPLE 16-LFCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。