参数资料
| 型号： | ADA4853-3YRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/21页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VIDEO TRIPLE 14-TSSOP |
| 标准包装： | 96 |
| 应用： | 电压反馈 |
| 输出类型： | 满摆幅 |
| 电路数： | 3 |
| -3db带宽： | 100MHz |
| 转换速率： | 120 V/µs |
| 电流 - 电源： | 1.4mA |
| 电流 - 输出 / 通道： | 160mA |
| 电压 - 电源，单路/双路(±)： | 2.65 V ~ 5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
ADA4853-1/ADA4853-2/ADA4853-3
Rev. F | Page 17 of 20
APPLICATIONS INFORMATION
SINGLE-SUPPLY VIDEO AMPLIFIER
With low differential gain and phase errors and wide 0.5 dB
flatness, the ADA4853-1/ADA4853-2/ADA4853-3 are ideal
solutions for portable video applications. Figure 51 shows a
typical video driver set for a noninverting gain of +2, where
RF = RG = 1 k. The video amplifier input is terminated into a
shunt 75 resistor. At the output, the amplifier has a series
75 resistor for impedance matching to the video load.
When operating in low voltage, single-supply applications, the
input signal is only limited by the input stage headroom.
75
CABLE
VOUT
75
75
VIN
RG
RF
+VS
PD
U1
C1
2.2F
C2
0.01F
05884-
043
+
V
Figure 51. Video Amplifier
POWER SUPPLY BYPASSING
Attention must be paid to bypassing the power supply pins of
the ADA4853-1/ADA4853-2/ADA4853-3. High quality capacitors
with low equivalent series resistance (ESR), such as multilayer
ceramic capacitors (MLCCs), should be used to minimize
supply voltage ripple and power dissipation. A large, usually
tantalum, 2.2 F to 47 F capacitor located in proximity to the
ADA4853-1/ADA4853-2/ADA4853-3 is required to provide
good decoupling for lower frequency signals. The actual value is
determined by the circuit transient and frequency requirements.
In addition, 0.1 F MLCC decoupling capacitors should be
located as close to each of the power supply pins as is physically
possible, no more than inch away. The ground returns should
terminate immediately into the ground plane. Locating the bypass
capacitor return close to the load return minimizes ground loops
and improves performance.
LAYOUT
As is the case with all high speed applications, careful attention
to printed circuit board (PCB) layout details prevents associated
board parasitics from becoming problematic. The ADA4853-1/
ADA4853-2/ADA4853-3 can operate at up to 100 MHz; there-
fore, proper RF design techniques must be employed. The PCB
should have a ground plane covering all unused portions of the
component side of the board to provide a low impedance return
path. Removing the ground plane on all layers from the area
near and under the input and output pins reduces stray capacit-
ance. Signal lines connecting the feedback and gain resistors
should be kept as short as possible to minimize the inductance
and stray capacitance associated with these traces. Termination
resistors and loads should be located as close as possible to their
respective inputs and outputs. Input and output traces should
be kept as far apart as possible to minimize coupling (crosstalk)
through the board. Adherence to microstrip or stripline design
techniques for long signal traces (greater than 1 inch) is
recommended. For more information on high speed board
layout, go to www.analog.com to view A Practical Guide to
High-Speed Printed-Circuit-Board Layout.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7837AR-REEL | IC DAC 12BIT DUAL MULT 24-SOIC |
| LTC1595BIS8#TRPBF | IC D/A CONV 16BIT MULTPLYNG8SOIC |
| LTC1595BIS8#TR | IC DAC 16BIT MULTIPLY SER 8SOIC |
| LT6552IDD#PBF | IC AMP VIDEO DIFF 3.3V 8-DFN |
| LT6207CGN#PBF | IC OP AMP VIDEO QUAD 3V 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4853-3YRUZ-R7 | 功能描述:IC OPAMP VIDEO TRIPLE 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ADA4853-3YRUZ-RL | 功能描述:IC OPAMP VIDEO TRIPLE 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ADA4855-3 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Supply, High Speed, Rail-to-Rail Output, Triple Op Amp |
| ADA4855-3YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4855-3YCP RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ADA4855-3YCPZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Triple Volt Fdbk R-R O/P 5.5V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:OP AMP TRIPLE VOLT FDBK R-R O/P 5.5V 16LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:IC OP-AMP 410MHZ 870V/ us LFCSP-16 制造商:Analog Devices 功能描述:IC, OP-AMP, 410MHZ, 870V/ us, LFCSP-16; Op Amp Type:High Speed; No. of Amplifiers:3; Slew Rate:870V/s; Supply Voltage Range:3V to 5.5V; Amplifier Case Style:LFCSP; No. of Pins:16; Bandwidth:410MHz; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。