参数资料
| 型号： | ADA4891-4ARZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R CMOS 14SOIC |
| 标准包装： | 56 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 输出类型： | 满摆幅 |
| 转换速率： | 210 V/µs |
| -3db带宽： | 240MHz |
| 电流 - 输入偏压： | 2pA |
| 电压 - 输入偏移： | 2500µV |
| 电流 - 电源： | 4.4mA |
| 电流 - 输出 / 通道： | 125mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 管件 |
ADA4891-1/ADA4891-2/ADA4891-3/ADA4891-4
Data Sheet
Rev. E | Page 18 of 24
TERMINATING UNUSED AMPLIFIERS
Terminating unused amplifiers in a multiamplifier package is
an important step in ensuring proper operation of the functional
amplifier. Unterminated amplifiers can oscillate and draw
excessive power. The recommended procedure for terminating
unused amplifiers is to connect any unused amplifiers in a
unity-gain configuration and to connect the noninverting input
to midsupply voltage. With symmetrical bipolar power supplies,
this means connecting the noninverting input to ground, as
shown in Figure 59.
08054-
064
–VS
+VS
ADA4891
Figure 59. Terminating Unused Amplifier with
Symmetrical Bipolar Power Supplies
In single power supply applications, a synthetic midsupply
source must be created. This can be accomplished with a simple
resistive voltage divider. Figure 60 shows the proper connection
for terminating an unused amplifier in a single-supply
configuration.
08054-
065
2.5k
+VS
ADA4891
Figure 60. Terminating Unused Amplifier with Single Power Supply
DISABLE FEATURE (ADA4891-3 ONLY)
The ADA4891-3 includes a power-down feature that can be
used to save power when an amplifier is not in use. When an
amplifier is powered down, its output goes to a high impedance
state. The output impedance decreases as frequency increases;
this effect can be observed in Figure 34. With the power-down
function, a forward isolation of 40 dB can be achieved at
50 MHz. Figure 46 shows the forward isolation vs. frequency
data. The power-down feature is asserted by pulling the PD1,
PD2, or PD3 pin low.
Table 7 summarizes the operation of the power-down feature.
Table 7. Disable Function
Power-Down Pin Connection (PDx)
Amplifier Status
>VTH or floating
Enabled
<VTH
Disabled
SINGLE-SUPPLY OPERATION
The ADA4891 can also be operated from a single power supply.
Figure 61 shows the ADA4891-3 configured as a single 5 V
supply video driver.
The input signal is ac-coupled into the amplifier via
Capacitor C1.
Resistor R2 and Resistor R4 establish the input midsupply
reference for the amplifier.
Capacitor C5 prevents constant current from being drawn
through the gain set resistor (RG) and enables the ADA4891-3
at dc to provide unity gain to the input midsupply voltage,
thereby establishing the output voltage at midsupply.
Capacitor C6 is the output coupling capacitor.
The large-signal frequency response obtained with single-
supply operation is identical to the bipolar supply operation
(Figure 18 shows the large-signal frequency response).
Four pairs of low frequency poles are formed by R2/2 and C2,
R3 and C1, RG and C5, and RL and C6. With this configuration,
the 3 dB cutoff frequency at low frequency is 12 Hz. The
values of C1, C2, C5, and C6 can be adjusted to change the low
frequency 3 dB cutoff point to suit individual design needs.
For more information about single-supply operation of op amps,
see the Analog Dialogue article “Avoiding Op Amp Instability
Problems in Single-Supply Applications” (Volume 35, Number 2)
08054-
086
C2
1F
R2
50kΩ
R4
50kΩ
R3
100kΩ
C1
22F
R1
50Ω
C6
22F
RL
150Ω
RG
453Ω
RF
453Ω
C5
22F
ADA4891-3
+5V
VOUT
VIN
–VS
C3
10F
C4
0.01F
+5V
Figure 61. Single-Supply Video Driver Schematic
相关PDF资料 |
PDF描述 |
|---|---|
| ADA4891-4ARUZ | IC OPAMP GP R-R CMOS 14TSSOP |
| AD8661ARZ | IC OPAMP GP R-R CMOS 4MHZ 8SOIC |
| AD8638ARZ | IC OPAMP CHOPPER R-R 37MA 8SOIC |
| LTC6101HVAHS5#TRMPBF | IC AMP CURRENT SENSE TSOT23-5 |
| 68046-242LF | CONN RCPT 84POS .100" DBL SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4891-4ARZ_PROMO | 制造商:Analog Devices 功能描述:OP-AMP 220MHZ 210V/US 3.1MV |
| ADA4891-4ARZ-R7 | 功能描述:IC OPAMP GP R-R CMOS 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| ADA4891-4ARZ-RL | 功能描述:IC OPAMP GP R-R CMOS 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| ADA4891-4WARUZ-R7 | 功能描述:高速运算放大器 Lw Cst CMOS Hgh Spd RR Amp Quad RoHS:否 制造商:NXP Semiconductors 通道数量: 电压增益 dB: 输入补偿电压: 转换速度: 工作电源电压: 电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SO-20 封装:Tube 产品: |
| ADA4895-1ARJZ-R2 | 功能描述:IC OPAMP GP 236MHZ RRO SOT23-6 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:在售 放大器类型:通用 电路数:1 输出类型:满摆幅 压摆率:943 V/μs -3db 带宽:236MHz 电流 - 输入偏置:11μA 电压 - 输入失调:53μV 电流 - 电源:3mA 电压 - 电源，单/双（±）:3 V ~ 10 V，±1.5 V ~ 5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商器件封装:SOT-23-6 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。