- 您现在的位置：买卖IC网 > PDF目录5723 > ADA4927-2YCPZ-R7 (Analog Devices Inc)IC OPAMP CF DIFF DUAL LN 24LFCSP PDF资料下载
参数资料
| 型号： | ADA4927-2YCPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CF DIFF DUAL LN 24LFCSP |
| 标准包装： | 1,500 |
| 放大器类型： | 电流反馈 |
| 电路数： | 2 |
| 输出类型： | 差分 |
| 转换速率： | 5000 V/µs |
| -3db带宽： | 2.3GHz |
| 电流 - 输入偏压： | 500nA |
| 电压 - 输入偏移： | 300µV |
| 电流 - 电源： | 20mA |
| 电流 - 输出 / 通道： | 65mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 11 V，±2.25 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 24-LFCSP-VQ（4x4） |
| 包装： | 带卷 (TR) |
ADA4927-1/ADA4927-2
Rev. A | Page 18 of 24
Table 12. Differential Input, DC-Coupled
Nominal Gain (dB)
RF (Ω)
RG (Ω)
RIN, dm (Ω)
Differential Output Noise Density (nV/√Hz)
0
301
602
8.0
20
442
44.2
88.4
21.8
26
604
30.1
60.2
37.9
Table 13. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 Ω
Nominal Gain (dB)
RF (Ω)
RG1 (Ω)
RT (Ω)
RIN, cm (Ω)
RG2 (Ω)1
Differential Output Noise Density (nV/√Hz)
0
309
301
56.2
401
328
8.1
20
511
39.2
158
73.2
77.2
18.6
26
806
28
649
54.2
74.4
29.1
1 RG2 = RG1 + (RS||RT).
Similar to the case of a conventional op amp, the output noise
voltage densities can be estimated by multiplying the input-
referred terms at +IN and IN by the appropriate output factor,
where:
(
)
2
1
N
β
G
+
=
2
is the circuit noise gain.
G1
F1
G1
1
R
β
+
=
R
and
G2
F2
G2
2
R
β
+
=
R
are the feedback factors.
When the feedback factors are matched, RF1/RG1 = RF2/RG2,
β1 = β2 = β, and the noise gain becomes
G
F
N
R
β
G
+
=
1
R
1
Note that the output noise from VOCM goes to zero in this case.
The total differential output noise density, vnOD, is the root-sum-
square of the individual output noise terms.
∑
=
1
i
2
nOi
nOD
v
8
resistor values, input impedance, and output noise density for
both balanced and unbalanced input configurations.
IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
As previously mentioned, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop still forces the outputs to remain balanced. The amplitudes
of the signals at each output remain equal and 180° out of phase.
The input-to-output differential mode gain varies proportionately
to the feedback mismatch, but the output balance is unaffected.
The gain from the VOCM pin to VO, dm is equal to
2(β1 β2)/(β1 + β2)
When β1 = β2, this term goes to zero and there is no differential
output voltage due to the voltage on the VOCM input (including
noise). The extreme case occurs when one loop is open and the
other has 100% feedback; in this case, the gain from VOCM input
to VO,dm is either +2 or 2, depending on which loop is closed.
The feedback loops are nominally matched to within 1% in
most applications, and the output noise and offsets due to the
VOCM input are negligible. If the loops are intentionally mismatched
by a large amount, it is necessary to include the gain term from
VOCM to VO, dm and account for the extra noise. For example, if
β1 = 0.5 and β2 = 0.25, the gain from VOCM to VO, dm is 0.67. If the
VOCM pin is set to 2.5 V, a differential offset voltage is present at the
output of (2.5 V)(0.67) = 1.67 V. The differential output noise
contribution is (15 nV/√Hz)(0.67) = 10 nV/√Hz. Both of these
results are undesirable in most applications; therefore, it is best
to use nominally matched feedback factors.
Mismatched feedback networks also result in a degradation of
the ability of the circuit to reject input common-mode signals,
much the same as for a four-resistor difference amplifier made
from a conventional op amp.
As a practical summarization of the previous issues, resistors of
1% tolerance produce a worst-case input CMRR of approximately
40 dB, a worst-case differential-mode output offset of 25 mV
due to a 2.5 V VOCM input, negligible VOCM noise contribution,
and no significant degradation in output balance error.
CALCULATING THE INPUT IMPEDANCE FOR AN
APPLICATION CIRCUIT
The effective input impedance of a circuit depends on whether
the amplifier is being driven by a single-ended or differential
signal source. For balanced differential input signals, as shown
(+DIN and DIN) is simply RIN, dm = RG + RG = 2 × RG.
+VS
–VS
ADA4927
+IN
–IN
RF
+DIN
–DIN
VOCM
RG
VOUT, dm
07
57
4-
04
8
Figure 48. The ADA4927 Configured for Balanced (Differential) Inputs
相关PDF资料 |
PDF描述 |
|---|---|
| 76382-414LF | CONN HEADER 14POS .100" R/A TIN |
| 170823-8 | CONN INSULATION SLEEVE .110 |
| 735075-1 | CONN RCPT HSG .250 1POS RED |
| MCP631T-E/OT | IC OP AMP SGL 24MHZ SOT23-5 |
| MCP631T-E/MNY | IC OP AMP SGL 24MHZ 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4927-2YCPZ-RL | 功能描述:IC OPAMP CF DIFF DUAL LN 24LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| ADA4930-1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Ultralow Noise Drivers for Low Voltage ADCs |
| ADA4930-1SCPZ-EPR2 | 制造商:Analog Devices 功能描述:ULTRALOW DIST LOW VLTG ADC DRIVER - Tape and Reel 制造商:Analog Devices 功能描述:Differential Amplifiers UltraLow Dist Low Vltg ADC Driver |
| ADA4930-1SCPZ-EPR7 | 制造商:Analog Devices 功能描述:ULTRALOW DIST LOW VLTG ADC DRIVER - Tape and Reel 制造商:Analog Devices 功能描述:IC OPAMP DIFF 1.35GHZ 16LFCSP |
| ADA4930-1SCPZ-EPRL | 制造商:Analog Devices 功能描述:ULTRALOW DIST LOW VLTG ADC DRIVER - Tape and Reel 制造商:Analog Devices 功能描述:IC OPAMP DIFF 1.35GHZ 16LFCSP 制造商:Analog Devices 功能描述:UltraLow Dist Low Vltg ADC Driver |
发布紧急采购，3分钟左右您将得到回复。