- 您现在的位置：买卖IC网 > PDF目录378277 > ADC0804 (Intersil, Corp.) 8-Bit, Microprocessor-Compatible A/D Converters PDF资料下载
参数资料
| 型号： | ADC0804 |
| 厂商： | Intersil, Corp. |
| 元件分类： | 串行ADC |
| 英文描述： | 8-Bit, Microprocessor-Compatible A/D Converters |
| 中文描述： | 8位微处理器兼容的A/D转换器 |
| 文件页数： | 10/16页 |
| 文件大小： | 250K |
| 代理商： | ADC0804 |
6-14
Input Source Resistance
Large values of source resistance where an input bypass
capacitor is not used will not cause errors since the input
currents settle out prior to the comparison time. If a low-
pass filter is required in the system, use a low-value series
resistor (
≤
1k
) for a passive RC section or add an op amp
RC active low-pass filter. For low-source-resistance
applications (
≤
1k
), a 0.1
μ
F bypass capacitor at the inputs
will minimize EMI due to the series lead inductance of a long
wire. A 100
series resistor can be used to isolate this
capacitor (both the R and C are placed outside the feedback
loop) from the output of an op amp, if used.
Stray Pickup
The leads to the analog inputs (pins 6 and 7) should be kept
as short as possible to minimize stray signal pickup (EMI).
Both EMI and undesired digital-clock coupling to these inputs
can cause system errors. The source resistance for these
inputs should, in general, be kept below 5k
. Larger values of
source resistance can cause undesired signal pickup. Input
bypass capacitors, placed from the analog inputs to ground,
will eliminate this pickup but can create analog scale errors as
these capacitors will average the transient input switching cur-
rents of the A/D (see Analog Input Current). This scale error
depends on both a large source resistance and the use of an
input bypass capacitor. This error can be compensated by a
full scale adjustment of the A/D (see Full Scale Adjustment)
with the source resistance and input bypass capacitor in
place, and the desired conversion rate.
Reference Voltage Span Adjust
For maximum application flexibility, these A/Ds have been
designed to accommodate a 5V, 2.5V or an adjusted voltage
reference. This has been achieved in the design of the IC as
shown in Figure 12.
Notice that the reference voltage for the IC is either
1
/
2
of the
voltage which is applied to the V+ supply pin, or is equal to
the voltage which is externally forced at the V
REF
/2 pin. This
allows for a pseudo-ratiometric voltage reference using, for
the V+ supply, a 5V reference voltage. Alternatively, a volt-
age less than 2.5V can be applied to the V
REF
/2 input. The
internal gain to the V
REF
/2 input is 2 to allow this factor of 2
reduction in the reference voltage.
Such an adjusted reference voltage can accommodate a
reduced span or dynamic voltage range of the analog input
voltage. If the analog input voltage were to range from 0.5V to
3.5V, instead of 0V to 5V, the span would be 3V. With 0.5V
applied to the V
lN(-)
pin to absorb the offset, the reference
voltage can be made equal to
1
/
2
of the 3V span or 1.5V. The
A/D now will encode the V
lN(+)
signal from 0.5V to 3.5V with
the 0.5V input corresponding to zero and the 3.5V input corre-
sponding to full scale. The full 8 bits of resolution are therefore
applied over this reduced analog input voltage range. The req-
uisite connections are shown in Figure 13. For expanded
scale inputs, the circuits of Figures 14 and 15 can be used.
FIGURE 12. THE V
REFERENCE
DESIGN ON THE IC
FIGURE 13. OFFSETTING THE ZERO OF THE ADC0802 AND
PERFORMING AN INPUT RANGE (SPAN)
ADJUSTMENT
FIGURE 14. HANDLING
±
10V ANALOG INPUT RANGE
V+
DGND
V
REF
/2
AGND
(V
REF
)
R
R
DIGITAL
CIRCUITS
ANALOG
CIRCUITS
9
8
10
20
DECODE
300
TO V
REF
/2
TO V
IN(-)
ZERO SHIFT VOLTAGE
0.1
μ
F
5V
-
+
V
REF
(5V)
FS
ADJ.
“SPAN”/2
ICL7611
V
IN(-)
2R
5V
2R
V
IN
±
10V
R
V
IN(+)
(V
REF
)
V+
20
10
μ
F
6
7
+
ADC0802-
ADC0804
ADC0802, ADC0803, ADC0804
相关PDF资料 |
PDF描述 |
|---|---|
| ADC08060 | 8-Bit, 20 MSPS to 60 MSPS, 1.3 mW/MSPS A/D Converter |
| ADC08060CIMT | 8-Bit, 20 MSPS to 60 MSPS, 1.3 mW/MSPS A/D Converter |
| ADC0806 | 8-Bit, 20 MSPS to 60 MSPS, 1.3 mW/MSPS A/D Converter |
| ADC08062 | 500 ns A/D Converter with S/H Function and Input Multiplexer |
| ADC08061 | 500 ns A/D Converter with S/H Function and Input Multiplexer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADC0804/D DIE | 制造商:Harris Corporation 功能描述: |
| ADC0804-1CD | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS 8-bit A/D converters |
| ADC0804-1CN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS 8-bit A/D converters |
| ADC0804-1LCD | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS 8-bit A/D converters |
| ADC0804-1LCN | 制造商:NXP Semiconductors 功能描述:Analog Digital Converter, Single, 8 Bit, 20 Pin, DIP |
发布紧急采购，3分钟左右您将得到回复。