参数资料
型号: ADC08100CIMTX
厂商: NATIONAL SEMICONDUCTOR CORP
元件分类: ADC
英文描述: 8-Bit, 20 MSPS to 100 MSPS, 1.3 mW/MSPS A/D Converter
中文描述: 1-CH 8-BIT RESISTANCE LADDER ADC, PARALLEL ACCESS, PDSO24
封装: TSSOP-24
文件页数: 12/19页
文件大小: 572K
代理商: ADC08100CIMTX
Specification Definitions
APERTURE (SAMPLING) DELAY
is that time required after
the fall of the clock input for the sampling switch to open. The
Sample/Hold circuit effectively stops capturing the input sig-
nal and goes into the “hold” mode t
AD
after the clock goes
low.
APERTURE JITTER
is the variation in aperture delay from
sample to sample. Aperture jitter shows up as input noise.
BOTTOM OFFSET
is the difference between the input volt-
age that just causes the output code to transition to the first
code and the negative reference voltage. Bottom Offset is
defined as E
OB
= V
ZT
– V
RB
, where V
ZT
is the first code
transition input voltage. V
RB
is the lower reference voltage.
Note that this is different from the normal Zero Scale Error.
CLOCK DUTY CYCLE
is the ratio of the time that the clock
waveform is at a logic high to the total time of one clock
period.
DIFFERENTIAL NON-LINEARITY (DNL)
is the measure of
the maximum deviation from the ideal step size of 1 LSB.
Measured at 100 MSPS with a ramp input.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS)
is another method of specifying Signal-to-Noise and
Distortion Ratio, or SINAD. ENOB is defined as (SINAD –
1.76) / 6.02 and says that the converter is equivalent to a
perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH
is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its low frequency value for a full scale input. The test
is performed with f
equal to 100 kHz plus integer multiples
of f
. The input frequency at which the output is 3 dB
relative to the low frequency input signal is the full power
bandwidth.
FULL-SCALE ERROR
is a measure of how far the last code
transition is from the ideal 1
1
2
LSB below V
RT
and is defined
as:
V
max
+ 1.5 LSB – V
RT
where V
max
is the voltage at which the transition to the
maximum (full scale) code occurs.
INTEGRAL NON-LINEARITY (INL)
is a measure of the
deviation of each individual code from a line drawn from zero
scale (
1
2
LSB below the first code transition) through positive
full scale (
1
2
LSB above the last code transition). The devia-
tion of any given code from this straight line is measured
from the center of that code value. The end point test method
is used. Measured at 100 MSPS with a ramp input.
INTERMODULATION DISTORTION (IMD)
is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to theADC input at the same time.
It is defined as the ratio of the power in the second and third
order intermodulation products to the power in one of the
original frequencies. IMD is usually expressed in dBFS.
MISSING CODE
are those output codes that are skipped
and will never appear at the ADC outputs. These codes
cannot be reached with any input value.
OUTPUT DELAY
is the time delay after the rising edge of
the input clock before the data update is present at the
output pins.
OUTPUT HOLD TIME
is the length of time that the output
data is valid after the rise of the input clock.
PIPELINE DELAY (LATENCY)
is the number of clock cycles
between initiation of conversion and when that data is pre-
sented to the output driver stage. New data is available at
every clock cycle, but the data lags the conversion by the
Pipeline Delay plus the Output Delay.
SIGNAL TO NOISE RATIO (SNR)
is the ratio, expressed in
dB, of the rms value of the input signal at the output to the
rms value of the sum of all other spectral components below
one-half the sampling frequency, not including harmonics or
dc.
SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or
SINAD)
is the ratio, expressed in dB, of the rms value of the
input signal at the output to the rms value of all of the other
spectral components below half the clock frequency, includ-
ing harmonics but excluding dc.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
is the differ-
ence, expressed in dB, between the rms values of the input
signal at the output and the peak spurious signal, where a
spurious signal is any signal present in the output spectrum
that is not present at the input.
TOTAL HARMONIC DISTORTION (THD)
is the ratio, ex-
pressed in dB, of the total of the first nine harmonic levels at
the output to the level of the fundamental at the output. THD
is calculated as
where F
1
is the RMS power of the fundamental (input)
frequency and f
2
through f
10
is the power in the first 9
harmonics in the output spectrum.
ZERO SCALE OFFSET ERROR
is the error in the input
voltage required to cause the first code transition. It is de-
fined as
V
OFF
= V
ZT
V
RB
where V
ZT
is the first code transition input voltage.
A
www.national.com
12
相关PDF资料
PDF描述
ADC0811 8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer
ADC0811BCN 8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer
ADC0811BCV 8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer
ADC0811CCJ 8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer
ADC0811CCN 8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer
相关代理商/技术参数
参数描述
ADC08100EVAL 功能描述:BOARD EVAL FOR ADC08100 RoHS:是 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像,彩色(RGB) 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ADC08100EVM 功能描述:ADC08100EVM 制造商:texas instruments 系列:* 零件状态:在售 标准包装:1
ADC0811 制造商:NSC 制造商全称:National Semiconductor 功能描述:8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer
ADC0811BCJ/A+ 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter, 8-Bit
ADC0811BCN 制造商:NSC 制造商全称:National Semiconductor 功能描述:8-Bit Serial I/O A/D Converter With 11-Channel Multiplexer