- 您现在的位置：买卖IC网 > PDF目录378277 > ADC08134 (National Semiconductor Corporation) 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function(8位高速串行输入/输出A/D转换器带多路选择，电压基准和跟踪/保持功能) PDF资料下载
参数资料
| 型号： | ADC08134 |
| 厂商： | National Semiconductor Corporation |
| 元件分类： | 串行ADC |
| 英文描述： | 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function(8位高速串行输入/输出A/D转换器带多路选择，电压基准和跟踪/保持功能) |
| 中文描述： | 8位高速串行I /办公自动化/ D的多路复用器选项，电压参考，并跟踪转换器/保持功能（8位高速串行输入/输出的A / D转换器带多路选择，电压基准和跟踪/保持功能） |
| 文件页数： | 13/21页 |
| 文件大小： | 483K |
| 代理商： | ADC08134 |
Functional Description
(Continued)
TABLE 3. MUX Addressing: ADC08138
(Continued)
Differential MUX Mode
MUX Address
SGL/
DIF
0
Analog Differential Channel-Pair
#
1
2
3
START
ODD/
SIGN
1
SELECT
1
1
0
2
3
0
1
0
1
4
5
6
7
+
1
TABLE 4. MUX Addressing: ADC08134
Single-Ended MUX Mode
MUX Address
SGL/
DIF
1
1
1
1
Channel
#
1
START
ODD/
SIGN
0
0
1
1
SELECT
1
0
1
0
1
0
2
3
1
1
1
1
+
+
+
+
COM is internally tied to AGND
Differential MUX Mode
MUX Address
SGL/
DIF
0
0
0
0
Channel
#
1
START
ODD/
SIGN
0
0
1
1
SELECT
1
0
1
0
1
0
2
3
1
1
1
1
+
+
+
+
Since the input configuration is under software control, it can
be modified as required before each conversion. A channel
can be treated as a single-ended, ground referenced input
for one conversion; then it can be reconfigured as part of a
differential channel for another conversion. Figure 1 illus-
trates the input flexibility which can be achieved.
The analog input voltages for each channel can range from
50 mV below ground to 50 mV above V
CC
(typically 5V)
without degrading conversion accuracy.
THE DIGITAL INTERFACE
A most important characteristic of these converters is their
serial data link with the controlling processor. Using a serial
communication format offers two very significant system
improvements; it allows many functions to be included in a
small package and it can eliminate the transmission of low
level analog signals by locating the converter right at the
analog sensor; transmitting highly noise immune digital data
back to the host processor.
To understand the operation of these converters it is best to
refer to the Timing Diagrams and Functional Block Diagram
and to follow a complete conversion sequence. For clarity a
separate timing diagram is shown for each device.
1.
A conversion is initiated by pulling the CS (chip select)
line low. This line must be held low for the entire con-
version. The converter is now waiting for a start bit and
its MUX assignment word.
2.
On each rising edge of the clock the status of the data in
(DI) line is clocked into the MUX address shift register.
The start bit is the first logic “1” that appears on this line
(all leading zeros are ignored). Following the start bit the
converter expects the next 2 to 4 bits to be the MUX
assignment word.
When the start bit has been shifted into the start location
of the MUX register, the input channel has been as-
signed and a conversion is about to begin. An interval of
1
2
clock period is automatically inserted to allow for
sampling the analog input. The SARS line goes high at
the end of this time to signal that a conversion is now in
progress and the DI line is disabled (it no longer accepts
data).
The data out (DO) line now comes out of TRI-STATE
and provides a leading zero.
During the conversion the output of the SAR comparator
indicates whether the analog input is greater than (high)
or less than (low) a series of successive voltages gen-
erated internally from a ratioed capacitor array (first 5
bits) and a resistor ladder (last 3 bits). After each com-
parison the comparator’s output is shipped to the DO
line on the falling edge of CLK. This data is the result of
the conversion being shifted out (with the MSB first) and
can be read by the processor immediately.
After 8 clock periods the conversion is completed. The
SARS line returns low to indicate this
1
2
clock cycle later.
3.
4.
5.
6.
A
www.national.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| ADC08138 | 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function(8位高速串行输入/输出A/D转换器带多路选择，电压基准和跟踪/保持功能) |
| ADC081500 | High Performance, Low Power, 8-Bit, 1.5 GSPS A/D Converter |
| ADC081500CIYB | High Performance, Low Power, 8-Bit, 1.5 GSPS A/D Converter |
| ADC081500EVAL | High Performance, Low Power, 8-Bit, 1.5 GSPS A/D Converter |
| ADC08161 | 500 ns A/D Converter with S/H Function and 2.5V Bandgap Reference(500ns带S/H功能和2.5V带隙参考的A/D转换器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADC08134BIJ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Single-Ended Data Acquisition System |
| ADC08134BIWM | 制造商:National Semiconductor 功能描述:08134 NAT SEMI |
| ADC08134CIJ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Single-Ended Data Acquisition System |
| ADC08134CIWM | 功能描述:IC ADC 8BIT HS SERIAL I/O 14SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| ADC08134CIWMX | 功能描述:IC ADC 8BIT HS SERIAL I/O 14SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
发布紧急采购，3分钟左右您将得到回复。