- 您现在的位置：买卖IC网 > Datasheet目录307 > ADE7769ARZ-RL (Analog Devices Inc)IC ENERGY METERING 1PHASE 16SOIC Datasheet资料下载
参数资料
| 型号： | ADE7769ARZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 16SOIC |
| 标准包装： | 2,500 |
| 输入阻抗： | 320 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 5mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
ADE7769
i ( t ) = I O + 2 × ∑ I h × sin ( hω t + β h )
∞
h ≠ o
(3)
Figure 17 shows the maximum signal levels on V1P and V1N.
The maximum differential voltage is ±30 mV. The differential
voltage signal on the inputs must be referenced to a common
where:
i(t) is the instantaneous current.
I 0 is the dc component.
I h is the rms value of current harmonic h.
β h is the phase angle of the current harmonic.
Using Equations 2 and 3, the real power (P) can be expressed in
terms of its fundamental real power (P 1 ) and harmonic real
power (P H ) as P = P 1 + P H
where:
mode, for example, AGND. The maximum common-mode
signal is ±6.25 mV, as shown in Figure 17.
Channel V2 (Voltage Channel)
The output of the line voltage sensor is connected to the
ADE7769 at this analog input. Channel V2 is a fully differential
voltage input with a maximum peak differential signal of
±165 mV. Figure 18 shows the maximum signal levels that can
be connected to the ADE7769 Channel V2.
V2
P 1 = V 1 × I 1 cos φ 1
(4)
+165mV
V2P
φ 1 = α 1 ? β 1
and
V CM
DIFFERENTIAL INPUT
± 165mV MAX PEAK
COMMON-MODE
± 25mV MAX
V2
V CM
V2N
∑ V h × I h cos φ h
P H =
∞
h ≠ 1
(5)
–165mV
AGND
φ h = α h ? β h
In Equation 5, a harmonic real power component is generated
for every harmonic, provided that harmonic is present in both
the voltage and current waveforms. The power factor calcu-
lation has previously been shown to be accurate in the case of a
pure sinusoid. Therefore, the harmonic real power must also
correctly account for the power factor because it is made up of
a series of pure sinusoids.
Note that the input bandwidth of the analog inputs is 7 kHz at
the nominal internal oscillator frequency of 450 kHz.
ANALOG INPUTS
Figure 18. Maximum Signal Levels, Channel V2
Channel V2 is usually driven from a common-mode voltage,
that is, the differential voltage signal on the input is referenced
to a common mode (usually AGND). The analog inputs of the
ADE7769 can be driven with common-mode voltages of up to
25 mV with respect to AGND. However, best results are
achieved using a common mode equal to AGND.
Typical Connection Diagrams
Figure 19 shows a typical connection diagram for Channel V1.
A shunt is the current sensor selected for this example because
of its low cost compared to other current sensors, such as the
current transformer (CT). This IC is ideal for low current meters.
Channel V1 (Current Channel)
R F
V1P
The voltage output from the current sensor is connected to the
ADE7769 here. Channel V1 is a fully differential voltage input.
V1P is the positive input with respect to V1N.
SHUNT
± 30mV
R F
C F
C F
V1N
The maximum peak differential signal on Channel V1 should
be less than ±30 mV (21 mV rms for a pure sinusoidal signal)
for specified operation.
V1
AGND
PHASE NEUTRAL
Figure 19. Typical Connection for Channel V1
Figure 20 shows a typical connection for Channel V2. Typically,
the line voltage. Adjusting the ratio of R A , R B , and R F is also a
+30mV
V CM
DIFFERENTIAL INPUT
± 30mV MAX PEAK
V1
V1P
V1N
the ADE7769 is biased around the phase wire, and a resistor
divider is used to provide a voltage signal that is proportional to
B
convenient way of carrying out a gain calibration on a meter.
COMMON-MODE
± 6.25mV MAX
V CM
–30mV
AGND
Figure 17. Maximum Signal Levels, Channel V1
Rev. A | Page 11 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| ADM8843ACPZ-REEL7 | IC LED DRVR WHITE BCKLGT 16LFCSP |
| ADP1653ACPZ-R7 | IC LED DRVR PHOTO FLASH 16-LFCSP |
| ADP1712-EVALZ | BOARD EVALUATION ADP1712 |
| ADP1720-EVALZ | BOARD EVAL FOR ADP1720-ADJ |
| ADP2140CPZ-REDYKIT | REDYKIT 2 BOARDS ADP2140ACPZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7816 | 制造商:AD 制造商全称:Analog Devices 功能描述:Six Current Channels, One Voltage Channel |
| ADE7816ACPZ | 功能描述:IC POWER METER 3 PHASE 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7816ACPZ-RL | 功能描述:IC ENERGY METERING 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7853ACPZ | 制造商:Analog Devices 功能描述: |
| ADE7854AACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 输入阻抗:400 千欧 测量误差:0.2% 电压 - I/O 高:2V，2.4V 电压 - I/O 低:0.4V，0.8V 电流 - 电源:20mA 电压 - 电源:2.8 V ~ 3.7 V 表计类型:3 相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘，CSP 供应商器件封装:40-LFCSP-WQ（6x6） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。