- 您现在的位置：买卖IC网 > PDF目录20633 > ADE7868ACPZ (Analog Devices Inc)IC ENERGY METERING 3PH 40LFCSP PDF资料下载
参数资料
| 型号： | ADE7868ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/100页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PH 40LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 400 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电流 - 电源： | 22mA |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
ADE7854/ADE7858/ADE7868/ADE7878
POWER-UP PROCEDURE
3.3V – 10%
2.0V ± 10%
ADE78xx
Data Sheet
PSM0 READY
0V
~26ms
~40ms
MICROPROCESSOR
MAKES THE
MICROPROCESSOR
SETS PM1 PIN TO 0;
APPLY VDD TO CHIP
POR TIMER
TURNED ON
ADE78xx
FULLY
POWERED UP
RSTDONE CHOICE BETWEEN
INTERRUPT I 2 C AND SPI
TRIGGERED
Figure 26. Power-Up Procedure
The ADE7854 / ADE7858 / ADE7868 / ADE7878 contain an on-
chip power supply monitor that supervises the power supply
(VDD). At power-up, the device is inactive until VDD reaches
2 V ± 10%. When VDD crosses this threshold, the power supply
monitor keeps the device in the inactive state for an additional
26 ms to allow VDD to rise to 3.3 V ? 10%, the minimum
recommended supply voltage.
The PM0 and PM1 pins have internal pull-up resistors, but it is
necessary to set the PM1 pin to Logic 0 either through a
microcontroller or by grounding the PM1 pin externally, before
powering up the chip. The PM0 pin can remain open as it is
held high, due to the internal pull-up resistor. This ensures that
PSM0 (normal) mode. The time taken from the chip being
powered up completely to the state where all functionality is
enabled, is about 40 ms (see Figure 26). It is necessary to ensure
that the RESET pin is held high during the entire power-up
procedure.
If PSM0 mode is the only desired power mode, the PM1 pin can
serial port. To use the SPI port, toggle the SS/HSA pin three times
from high to low.
To lock I 2 C as the active serial port, set Bit 1 (I2C_LOCK) of the
CONFIG2 register to 1. From this moment, the device ignores
spurious toggling of the SS/HSA pin, and a switch to the SPI
Immediately after entering PSM0 mode, all registers in the
values, including the CONFIG2 and LPOILVL registers.
The ADE7854 / ADE7858 / ADE7868 / ADE7878 signal the end of
the transition period by pulling the IRQ1 interrupt pin low and
setting Bit 15 (RSTDONE) in the STATUS1 register to 1. This
bit is cleared to 0 during the transition period and is set to 1
when the transition ends. Writing the STATUS1 register with
the RSTDONE bit set to 1 clears the status bit and returns the
IRQ1 pin high. Because RSTDONE is an unmaskable interrupt,
Bit 15 (RSTDONE) in the STATUS1 register must be cancelled
for the IRQ1 pin to return high. Wait until the IRQ1 pin goes low
before accessing the STATUS1 register to test the state of the
RSTDONE bit. At this point, as a good programming practice,
cancel all other status flags in the STATUS1 and STATUS0 registers
by writing the corresponding bits with 1.
Initially, the DSP is in idle mode and, therefore, does not
execute any instructions. This is the moment to initialize all
See the Digital Signal Processor section for the proper procedure
to initialize all registers and start the metering.
If the supply voltage, VDD, falls lower than 2 V ± 10%, the
state, which means that no measurements or computations
are executed.
port is no longer possible.
If SPI is the active serial port, any write to the CONFIG2 register
locks the port, and a switch to the I 2 C port is no longer possible.
must be powered down or the device must be reset by setting
the RESET pin low. After the serial port is locked, the serial port
selection is maintained when the device changes from one
PSMx power mode to another.
Rev. H | Page 26 of 100
相关PDF资料 |
PDF描述 |
|---|---|
| EMA50DTMD-S664 | CONN EDGECARD 100PS R/A .125 SLD |
| T95Y106M020LZAL | CAP TANT 10UF 20V 20% 2910 |
| GEM15DRSH | CONN EDGECARD 30POS DIP .156 SLD |
| GMC49DRAS-S734 | CONN EDGECARD 98POS .100 R/A SLD |
| R1D12-1509/P | CONV DC/DC 1W 15VIN +/-09VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7868ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7878 | 制造商:AD 制造商全称:Analog Devices 功能描述:Polyphase Multifunction Energy Metering IC with per Phase Active and Reactive Powers |
| ADE7878AACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 输入阻抗:400 千欧 测量误差:0.2% 电压 - I/O 高:2V，2.4V 电压 - I/O 低:0.4V，0.8V 电流 - 电源:20mA 电压 - 电源:2.8 V ~ 3.7 V 表计类型:3 相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘，CSP 供应商器件封装:40-LFCSP-WQ（6x6） 标准包装:1 |
| ADE7878AACPZ-RL | 功能描述:IC ENERGY METER MULTIFUN 40LFCSP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 输入阻抗:400 千欧 测量误差:0.2% 电压 - I/O 高:2V，2.4V 电压 - I/O 低:0.4V，0.8V 电流 - 电源:20mA 电压 - 电源:2.8 V ~ 3.7 V 表计类型:3 相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘，CSP 供应商器件封装:40-LFCSP-WQ（6x6） 标准包装:2,500 |
| ADE7878ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
发布紧急采购，3分钟左右您将得到回复。