- 您现在的位置：买卖IC网 > PDF目录8875 > ADG3308BCBZ-1-RL7 (Analog Devices Inc)IC XLATOR 8CH 1.2-5.5V 20-WLCSP PDF资料下载
参数资料
| 型号： | ADG3308BCBZ-1-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC XLATOR 8CH 1.2-5.5V 20-WLCSP |
| 产品变化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 标准包装： | 1 |
| 逻辑功能： | 变换器，双向 |
| 位数： | 8 |
| 输入类型： | 逻辑 |
| 输出类型： | 逻辑 |
| 数据速率： | 50Mbps |
| 通道数： | 8 |
| 输出/通道数目： | 1 |
| 差分 - 输入:输出： | 无/无 |
| 传输延迟（最大）： | 6ns |
| 电源电压： | 1.15 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-UFBGA，WLCSP |
| 供应商设备封装： | 20-WLCSP |
| 包装： | 标准包装 |
| 其它名称： | ADG3308BCBZ-1-RL7DKR |
ADG3308/ADG3308-1
Data Sheet
Rev. D | Page 16 of 20
THEORY OF OPERATION
The ADG3308/ADG3308-1 level translators allow the level
shifting necessary for data transfer in a system where multiple
supply voltages are used. The device requires two supplies, VCCA
and VCCY (VCCA ≤ VCCY). These supplies set the logic levels on
each side of the device. When driving the A pins, the device
translates the VCCA compatible logic levels to VCCY compatible
logic levels available at the Y pins. Similarly, because the device
is capable of bidirectional translation, when driving the Y pins
the VCCY compatible logic levels are translated to the VCCA
compatible logic levels available at the A pins. When EN = 0,
the A1 pin to the A8 pin and the Y1 pin to the Y8 pin are three-
stated. When EN is driven high, the ADG3308/ADG3308-1 go
into normal operation mode and perform level translation.
LEVEL TRANSLATOR ARCHITECTURE
The ADG3308/ADG3308-1 consist of eight bidirectional
channels. Each channel can translate logic levels in either the
A→Y or the Y→A direction. They use a one-shot accelerator
architecture, ensuring excellent switching characteristics.
Figure 39 shows a simplified block diagram of a bidirectional
channel.
ONE-SHOT GENERATOR
6k
Y
VCCA
VCCY
T2
T1
T3
T4
A
P
N
U1
U2
U4
U3
04865-
053
Figure 39. Simplified Block Diagram of an
ADG3308/ADG3308-1 Channel
The logic level translation in the A→Y direction is performed
using a level translator (U1) and an inverter (U2), whereas the
translation in the Y→A direction is performed using the U3
inverter and U4 inverter. The one-shot generator detects a rising
or falling edge present on either the A side or the Y side of the
channel. It sends a short pulse that turns on the PMOS transistors
(T1 and T2) for a rising edge, or the NMOS transistors (T3 and
T4) for a falling edge. This charges/discharges the capacitive load
faster, resulting in fast rise and fall times.
The inputs of the unused channels (A or Y) should be tied to
their corresponding VCC rail (VCCA or VCCY) or to GND.
INPUT DRIVING REQUIREMENTS
To ensure correct operation of the ADG3308/ADG3308-1,
the circuit that drives the input of the device should be able
to ensure rise/fall times of less than 3 ns when driving a
load consisting of a 6 k resistor in parallel with the input
capacitance of the ADG3308/ADG3308-1 channel.
OUTPUT LOAD REQUIREMENTS
The ADG3308/ADG3308-1 level translators are designed to
drive CMOS-compatible loads. If current-driving capability
is required, it is recommended to use buffers between the
ENABLE OPERATION
The ADG3308/ADG3308-1 provide three-state operation at the
A I/O pins and the Y I/O pins by using the enable (EN) pin, as
shown in Table 4.
Table 4. Truth Table
EN
Y I/O Pins
A I/O Pins
0
High-Z1
1
Normal operation2
1
High impedance state.
2
In normal operation, the ADG3308/ADG3308-1 perform level translation.
When EN = 0, the ADG3308/ADG3308-1 enter into three-state
mode. In this mode, the current consumption from both the
VCCA and VCCY supplies is reduced, allowing the user to save
power, which is critical, especially in battery-operated systems.
The EN input pin can only be driven with VCCY compatible logic
levels for the ADG3308, whereas the ADG3308-1 can be driven
with either VCCA- or VCCY compatible logic levels.
POWER SUPPLIES
For proper operation of the device, the voltage applied to the
VCCA must always be less than or equal to the voltage applied
to VCCY. To meet this condition, the recommended power-up
operate properly only after both supply voltages reach their
nominal values. It is not recommended to use the part in a system
where, during power-up, VCCA may be greater than VCCY due to
a significant increase in the current taken from the VCCA supply.
For optimum performance, the VCCA and VCCY pins should be
decoupled to GND as close as possible to the device.
相关PDF资料 |
PDF描述 |
|---|---|
| ADG3308BCBZ-1-REEL | IC XLATOR 8CH 1.2-5.5V 20-WLCSP |
| ADG3308BCPZ-REEL | IC XLATOR 8CH 1.2-5.5V 20LFCSP |
| SY100EPT23LKG | IC XLATOR DUAL DIFF 3.3V 8-MSOP |
| SY10EPT28LZG TR | IC TRANSLATOR 3V DIFF 8-SOIC |
| SY10EPT28LKG TR | IC TRANSLATOR LVPECL 3V 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADG3308BCBZ-2-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Voltage, 1.15 V to 5.5 V, 8-Channel Bidirectional Logic Level Translators |
| ADG3308BCBZ-2-RL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Voltage, 1.15 V to 5.5 V, 8-Channel Bidirectional Logic Level Translators |
| ADG3308BCP | 制造商:Analog Devices 功能描述:LOW VOLTAGE 1.2 V TO 5.5 V, BIDIRECTIONAL, LOGIC LEVEL TRANS - Bulk |
| ADG3308BCPZ | 制造商:Analog Devices 功能描述: |
| ADG3308BCPZ-REEL | 功能描述:IC XLATOR 8CH 1.2-5.5V 20LFCSP RoHS:是 类别:集成电路 (IC) >> 逻辑 - 变换器 系列:- 产品培训模块:Logic Packages 标准包装:2,500 系列:- 逻辑功能:变换器，双向 位数:2 输入类型:电压 输出类型:电压 数据速率:- 通道数:2 输出/通道数目:1 差分 - 输入:输出:无/无 传输延迟（最大）:1.5ns 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:带卷 (TR) 其它名称:935284857118GTL2002DP/S440-TGTL2002DP/S440-T-ND |
发布紧急采购，3分钟左右您将得到回复。