- 您现在的位置：买卖IC网 > PDF目录11485 > ADG4612BRUZ (Analog Devices Inc)IC SWITCH QUAD SPST 16TSSOP PDF资料下载
参数资料
| 型号： | ADG4612BRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPST 16TSSOP |
| 设计资源： | Power off protected data acquisition signal chain using ADG4612 , AD711, and AD7476 (CN0165) |
| 标准包装： | 96 |
| 功能： | 开关 |
| 电路： | 4 x SPST - NO |
| 导通状态电阻： | 5.1 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 12 V，±3 V ~ 5.5 V |
| 电流 - 电源： | 600µA |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
ADG4612/ADG4613
Rev. 0 | Page 16 of 24
TERMINOLOGY
IDD
IDD represents the positive supply current.
ISS
ISS represents the negative supply current.
VD, VS
VD and VS represent the analog voltage on Terminal D and
Terminal S, respectively.
RON
RON represents the ohmic resistance between Terminal D and
Terminal S.
ΔRON
ΔRON represents the difference between the RON of any two
channels.
RFLAT (ON)
Flatness that is defined as the difference between the maximum
and minimum value of on resistance measured over the specified
analog signal range is represented by RFLAT (ON).
IS (Off)
IS (Off) is the source leakage current with the switch off.
ID (Off)
ID (Off) is the drain leakage current with the switch off.
ID (On), IS (On)
ID (On) and IS (On) represent the channel leakage currents with
the switch on.
VINL
VINL is the maximum input voltage for Logic 0.
VINH
VINH is the minimum input voltage for Logic 1.
IINL, IINH
IINL and IINH represent the low and high input currents of the
digital inputs.
CD (Off)
CD (Off) represents the off switch drain capacitance, which is
measured with reference to ground.
CS (Off)
CS (Off) represents the off switch source capacitance, which is
measured with reference to ground.
CD (On), CS (On)
CD (On) and CS (On) represent on switch capacitances, which
are measured with reference to ground.
CIN
CIN is the digital input capacitance.
tON
tON represents the delay between applying the digital control
input and the output switching on.
tOFF
tOFF represents the delay between applying the digital control
input and the output switching off.
tD
tD represents the off time measured between the 80% point of
both switches when switching from one address state to
another.
Fault Response Time
Fault response time is the delay between a fault condition (VS >
VDD) on an analog input and the corresponding output below VDD.
Fault Recovery Time
Fault recovery time is, in recovering from a fault condition, the
delay between 50% of the input signal to 90% of the output
signal.
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching.
Off Isolation
Off isolation is a measure of unwanted signal coupling through
an off switch.
Charge Injection
Charge injection is a measure of the glitch impulse transferred
from the digital input to the analog output during switching.
Crosstalk
Crosstalk is a measure of unwanted signal that is coupled
through from one channel to another as a result of parasitic
capacitance.
Bandwidth
Bandwidth is the frequency at which the output is attenuated
by 3 dB.
On Response
On response is the frequency response of the on switch.
Insertion Loss
Insertion loss is the loss due to the on resistance of the switch.
Total Harmonic Distortion + Noise (THD + N)
The ratio of the harmonic amplitude plus noise of the signal to
the fundamental is represented by THD + N.
AC Power Supply Rejection Ratio (ACPSRR)
ACPSRR is the ratio of the amplitude of signal on the output to
the amplitude of the modulation. This is a measure of the ability
of the part to avoid coupling noise and spurious signals that appear
on the supply voltage pin to the output of the switch. The dc
voltage on the device is modulated by a sine wave of 0.62 V p-p.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B4W-CU-F4 | CONVERTER MOD DC/DC 5.5V 200W |
| VE-B4W-CU-F3 | CONVERTER MOD DC/DC 5.5V 200W |
| ADG1604BRUZ | IC MULTIPLEXER 4X1 14TSSOP |
| SST89E58RD2A-40-I-TQJE-T | IC MCU 8BIT 40KB FLASH 44TQFP |
| ADG412BNZ | IC SWITCH QUAD SPST 16DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADG4612BRUZ-REEL7 | 功能描述:模拟开关 IC 5V 4 x SPST Known Power Off RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| ADG4613BCPZ-REEL7 | 功能描述:IC SWITCH QUAD SPST 16LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 标准包装:1,000 系列:- 功能:多路复用器 电路:1 x 4:1 导通状态电阻:- 电压电源:双电源 电压 - 电源，单路/双路(±):±5V 电流 - 电源:7mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ADG4613BRUZ | 功能描述:IC SWITCH QUAD SPST 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 功能:开关 电路:单刀单掷 导通状态电阻:48 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电流 - 电源:5µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:托盘 |
| ADG4613BRUZ-REEL7 | 功能描述:模拟开关 IC 5V 4 x SPST Known Power Off RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| ADG465 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Channel Protector in an SOT-23 Package |
发布紧急采购，3分钟左右您将得到回复。