参数资料
| 型号： | ADG795GBCPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX 2X1 24LFCSP |
| 产品变化通告： | ADG79xx Discontinuance Notice 17/Aug/2010 |
| 标准包装： | 1 |
| 功能： | 多路复用器/多路分解器 |
| 电路： | 5 x 2:1 |
| 导通状态电阻： | 4 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 3V，5V |
| 电流 - 电源： | 1nA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 24-LFCSP-VQ（4x4） |
| 包装： | 标准包装 |
| 其它名称： | ADG795GBCPZ-REELDKR |
ADG795A/ADG795G
Rev. 0 | Page 17 of 24
THEORY OF OPERATION
The ADG795A/ADG795G are monolithic CMOS devices
comprising five 2:1 multiplexers controllable via a standard I2C
serial interface. The CMOS process provides ultralow power
dissipation, yet offers high switching speed and low on resistance.
The on resistance profile is very flat over the full analog input
range, and wide bandwidth ensures excellent linearity and low
distortion. These features, combined with a wide input signal
range, make the ADG795A/ADG795G an ideal switching
solution for a wide range of TV applications.
The switches conduct equally well in both directions when on.
In the off condition, signal levels up to the supplies are blocked.
The integrated serial I2C interface controls the operation of the
switches (ADG795A/ADG795G) and general-purpose logic
pins (ADG795G only).
The ADG795A/ADG795G have many attractive features, such as
the ability to individually control each multiplexer, the option of
reading back the status of any switch. The ADG795G has one
general-purpose logic output pin controllable through the I2C
interface. The following sections describe these features in detail.
I2C SERIAL INTERFACE
The ADG795A/ADG795G are controlled via an I2C-compatible
serial bus interface (refer to the I2C-Bus Specification available
from Philips Semiconductor) that allows the part to operate as a
slave device (no clock is generated by the ADG795A/ADG795G).
The communication protocol between the I2C master and the
device operates as follows:
1.
The master initiates data transfer by establishing a start
condition (defined as a high-to-low transition on the SDA
line while SCL is high). This indicates that an address/data
stream follows. All slave devices connected to the bus
respond to the start condition and shift in the next eight
bits, consisting of a seven bit address (MSB first) plus an
R/W bit. This bit determines the direction of the data flow
during the communication between the master and the
addressed slave device.
2.
The slave device whose address corresponds to the trans-
mitted address responds by pulling the SDA line low during
the ninth clock pulse (this is called the acknowledge bit).
At this stage, all other devices on the bus remain idle while
the selected device waits for data to be written to, or read
from, its serial register. If the R/W bit is set high, the
master reads from the slave device. However, if the R/W bit
is set low, the master writes to the slave device.
3.
Data transmits over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge
bit). The transitions on the SDA line must occur during the
low period of the clock signal, SCL, and remain stable
during the high period of SCL. Otherwise, a low-to-high
transition when the clock signal is high can be interpreted
as a stop event that ends the communication between the
master and the addressed slave device.
4.
After transferring all data bytes, the master establishes a
stop condition, defined as a low-to-high transition on the
SDA line while SCL is high. In write mode, the master pulls
the SDA line high during the 10th clock pulse to establish a
stop condition. In read mode, the master issues a no
acknowledge for the ninth clock pulse (the SDA line
remains high). The master then brings the SDA line low
before the 10th clock pulse, and then high during the 10th
clock pulse to establish a stop condition.
I2C ADDRESS
The ADG795A/ADG795G have a 7-bit I2C address. The four
most significant bits are internally hardwired and last three bits
(A0, A1, and A2) are user-adjustable. This allows the user to
connect up to eight ADG795As/ADG795Gs to the same bus. The
I2C bit map shows the configuration of the 7-bit address.
7-Bit I2C Address Configuration
MSB
LSB
1
0
1
0
A2
A1
A0
WRITE OPERATION
When writing to the ADG795A/ADG795G, the user must
begin with an address byte and R/W bit, after which time the
switch acknowledges that it is prepared to receive data by
pulling SDA low. Data is loaded into the device as a 16-bit word
under the control of a serial clock input, SCL. Figure 31
illustrates the entire write sequence for the ADG795A/
ADG795G. The first data byte (AX7 to AX0) controls the status
of the switches while the LDSW and RESETB bits from the
second byte control the operation mode of the device. Table 6
shows a list of all commands supported by the ADG795A/
ADG795G with the corresponding byte that needs to be loaded
during a write operation.
To achieve the desired configuration, one or more commands
can be loaded into the device. Any combination of the
commands in Table 6 can be used with these restrictions:
Only one switch from a given multiplexer can be on at any
given time.
When a sequence of successive commands affect the same
element (that is, the switch or GPO pin), only the last
command is executed.
OBSOLETE
相关PDF资料 |
PDF描述 |
|---|---|
| ADG796ABCPZ-REEL | IC MUX/DEMUX HEX 2X1 24LFCSP |
| ADG799GBCPZ-REEL | IC CROSSPOINT SWIT TRPL 24LFCSP |
| ADG802BRT-REEL7 | IC SWITCH SPST SOT23-6 |
| ADG804YRM | IC MULTIPLEXER 4X1 10MSOP |
| ADG813YRU | IC SWITCH QUAD SPST 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADG795GCCPZ-500RL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:I2C-Compatible, Wide Bandwidth, Five 2:1 Multiplexer |
| ADG795GCCPZ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:I2C-Compatible, Wide Bandwidth, Five 2:1 Multiplexer |
| ADG796A | 制造商:AD 制造商全称:Analog Devices 功能描述:I2C-Compatible, Wide Bandwidth, Hex 2:1 Multiplexer |
| adg796abcpz-500rl7 | 制造商:Analog Devices 功能描述:ANLG MUX HEX 2:1 5V 24LFCSP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: |
| ADG796ABCPZ-REEL | 功能描述:IC MUX/DEMUX HEX 2X1 24LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 标准包装:1 系列:- 功能:开关 电路:2 x SPST - NC/NO 导通状态电阻:8 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):2.3 V ~ 4.3 V 电流 - 电源:1µA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-迷你型QFN（1.4x1.4） 包装:剪切带 (CT) 其它名称:DG2738DN-T1-E4CT |
发布紧急采购，3分钟左右您将得到回复。