参数资料
| 型号： | ADL5565ACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF 6GHZ 16LFCSP |
| 特色产品： | RF ICs |
| 标准包装： | 1 |
| 放大器类型： | RF/IF 差分 |
| 电路数： | 1 |
| 转换速率： | 11000 V/µs |
| -3db带宽： | 7GHz |
| 电流 - 输入偏压： | 5µA |
| 电流 - 电源： | 80mA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 2.8 V ~ 5.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-WQ（3x3） |
| 包装： | 标准包装 |
| 其它名称： | ADL5565ACPZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ADL5565
Data Sheet
C3
10F
C4
0.1F
C5
0.1F
C6
0.1F
C7
0.1F
C8
0.1F
C13
OPEN
C11
0.1F
VPOS
R9
34.8
R11
OPEN
R15
OPEN
R14
0
J3
R10
34.8
R8
84.5
C10
0.01F
C9
0.01F
P1
T2
VCOM
AGND
VPOS
GND
R7
84.5
ENBL
J4
OPEN
R12
OPEN
R13
0
J2
OPEN
ADL5565
9
10
11
12
4
3
2
1
16
15
14
13
5
6
7
8
GND
VCC
VIN1
VIN2
VIP2
VIP1
VON
VCOM
ENBL
VOP
VCC
C12
OPEN
J1
T1
R1
OPEN
R2
OPEN
R4
0
R3
0
R5
0
R6
0
C1
0.01F
C2
0.01F
09959-
046
Figure 45. Evaluation Board Schematic
Table 16. Evaluation Board Configuration Options
Component
Description
Default Condition
VPOS, GND
Ground and supply vector pins.
VPOS, GND = installed
C3, C4, C5,
C6, C7, C11
Power supply decoupling. The supply decoupling consists of a 10 F capacitor (C3) to
ground. C4 to C7 are bypass capacitors. C11 ac couples VREF to ground.
C3 = 10 F (Size D),
C4, C5, C6, C7, C11 = 0.1 F (Size 0402)
J1, J2, R1, R2,
R3, R4, R5, R6,
R12, R13, C1,
C2, C12, T1
Input interface. The SMA labeled J1 is the input. T1 is a 1-to-1 impedance ratio balun
to transform a single-ended input into a balanced differential signal. Removing R13,
installing R12 (0 ), and installing an SMA connector (J2) allows driving from a
differential source. C1 and C2 provide ac coupling. C12 is a bypass capacitor. R1 and
R2 provide a differential 50 input termination. R3 to R6 are used to select the input
for the pin-strappable gain. The maximum gain is R3, R4, R5, R6 = 0 and R1 and R2 =
open. The middle gain is R5 and R6 = 0 , R3 and R4 = open, and R1 and R2 = 50 . The
minimum gain is R3 and R4 = 0 , R5 and R6 = open, and R1 and R2 = 33.2 .
J1 = installed, J2 = not installed,
R1, R2 = open,
R3, R4, R5, R6, R13 = 0 (Size 0402),
R12, = open,
C1, C2 = 0.01 F (Size 0402),
C12 = open,
T1 = ETC1-1-13 (M/A-COM)
J3, J4, R7, R8,
R9, R10, R11,
R14, R15 C9,
C10, C13, T2
Output interface. The SMA labeled J3 is the output. T2 is a 1-to-1 impedance ratio balun
to transform a balanced differential signal to a single-ended signal. Removing R14,
installing R15 (0 ), and installing an SMA connector (J4) allows differential loading. C13 is
a bypass capacitor. R7, R8, R9, and R10 are provided for generic placement of matching
components. The evaluation board is configured to provide a 200 to 50 impedance
transformation with an insertion loss of 17 dB. C9 and C10 provide ac coupling.
J3 = installed, J4 = not installed,
R7, R8 = 84.5 (Size 0402),
R9, R10 = 34.8 (Size 0402),
R11, R15 = open (Size 0402),
R14 = 0 (Size 0402)
C9, C10 = 0.01 F (Size 0402),
C13 = open
T2 = ETC1-1-13 (M/A-COM)
ENBL, P1, C8
Device enabled. C8 is a bypass capacitor. When the P1 jumper is set toward the VPOS label,
the ENBL pin is connected to the supply, enabling the device. In the opposite direction,
toward the GND label, the ENBL pin is grounded, putting the device in power-down mode.
ENBL, P1 = installed,
C8 = 0.1 F (Size 0402)
Table 17. Differential Values for Figure 45
Gain (dB)
R1 ()
R2 ()
6
29
12
33
15.5
Open
Table 18. Alternative Differential Input Configuration for Figure 45
Gain (dB)
R1 and R2 ()
C12 (F)
C1 and C2 ()
T1
6
Open
0.1
0
Mini Circuits TC4-1W+
12
Open
0.1
0
Mini Circuits TC2-1T+
15.5
Open
0.1
0
Mini Circuits TC1.5-52T+
Rev. E | Page 24 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| ADM4073TWRJZ-REEL7 | IC AMP CS 1.8MHZ SOT23-6 |
| ADMP401ACEZ-RL | MIC MEMS OMNI-DIR ANALOG 6-LGA |
| ADMP404ACEZ-RL | MIC MEMS OMNI-DIR ANALOG 3LGA |
| ADMP405ACEZ-RL7 | MIC MEMS OMNI-DIR ANALOG 3-LGA |
| ADMP421ACEZ-RL | MIC MEMS OMNI-DIR DIGITAL 5-LGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADL5565ACPZ-R7 | 制造商:Analog Devices 功能描述:IC, RF AMP, 15.5dB, 6GHz, 5.2V, LFCSP-16 |
| ADL5565-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) 制造商:Analog Devices 功能描述:EVAL 6GHZ DIFFERENT AMP ADL5565 制造商:Analog Devices 功能描述:ADL5565, DIFF AMPLIFIER, EVAL BOARD 制造商:Analog Devices 功能描述:ADL5565, DIFF AMPLIFIER, EVAL BOARD; Silicon Manufacturer:Analog Devices; Kit Application Type:Amplifier; Application Sub Type:Differential Amplifier; Features:Differential / Single-ended Input to Differential Output, Low Broadband ;RoHS Compliant: Yes |
| ADL5566ACPZ-R7 | 功能描述:射频放大器 6 GHz Ultrahigh Dyn Rg Diff Amp RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| ADL5566-EVALZ | 制造商:Analog Devices 功能描述:ADL5566 EVALUATION BOARD - Boxed Product (Development Kits) |
| ADL5567ACPZN-R7 | 功能描述:Differential Amplifier 2 Circuit 24-LFCSP (4x4) 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:在售 放大器类型:差分 电路数:2 输出类型:- 压摆率:20000 V/μs 增益带宽积:- -3db 带宽:4.3GHz 电流 - 输入偏置:- 电压 - 输入失调:- 电流 - 电源:148mA 电流 - 输出/通道:- 电压 - 电源，单/双（±）:3.3V，5V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-WFQFN 裸露焊盘 供应商器件封装:24-LFCSP（4x4） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。