- 您现在的位置：买卖IC网 > PDF目录16755 > ADM00313 (Microchip Technology)BOARD EVAL LI-ION CHRG MCP73830L PDF资料下载
参数资料
| 型号： | ADM00313 |
| 厂商： | Microchip Technology |
| 文件页数： | 13/30页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LI-ION CHRG MCP73830L |
| 设计资源： | MCP73830L Eval Bd Gerber |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MCP73830L |
| 主要属性： | 1 芯锂离子电池 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
MCP73830/L
5.0
DETAILED DESCRIPTION
5.2.3
BATTERY DETECTION
The MCP73830/L device detects the battery presence
5.1
Undervoltage Lockout (UVLO)
by monitoring the voltage at V BAT . The charge flow will
An Internal Undervoltage Lockout (UVLO) circuit
monitors the input voltage and keeps the charger in
Shutdown mode until the input supply rises above the
UVLO threshold. In the event a battery is present when
the input power is applied, the input supply must rise
approximately 150 mV above the battery voltage
before the MCP73830/L devices become operational.
initiate when the voltage on V BAT is pulled below the
cal Characteristics” for V RECHARGE values. The value
will be the same for non-rechargeable devices.
When V BAT > V REG + Hysteresis, the charge will be
suspended or not started, depending on the condition,
to prevent the overcharge that may occur.
The UVLO circuit places the device in Shutdown mode
if the input supply falls to approximately 150 mV above
5.3
Preconditioning
the battery voltage. The UVLO circuit is always active.
Any time the input supply is below the UVLO threshold,
or approximately 150 mV of the voltage at the V BAT pin,
the MCP73830/L devices are placed in Shutdown
mode.
If the voltage at the V BAT pin is less than the precondi-
tioning threshold, the MCP73830/L devices enter
Preconditioning mode. The preconditioning threshold
teristics” for preconditioning threshold options.
5.2
Charge Qualification
In this mode, the MCP73830/L devices supply 10% of
the fast charge current (established with the value of
When the input power is applied, the input supply must
rise 150 mV above the battery voltage before the
MCP73830/L becomes operational.
The automatic power-down circuit places the device in
Shutdown mode if the input supply falls to within
the resistor connected to the PROG pin) to the battery.
When the voltage at the V BAT pin rises above the pre-
conditioning threshold, the MCP73830/L device enters
the Constant Current (Fast Charge) mode.
+50 mV of the battery voltage.
The automatic circuit is always active. Any time the
input supply is within +50 mV of the voltage at the
Note:
5.3.1
The MCP73830/L devices also offer
options with no preconditioning.
TIMER EXPIRED DURING
V BAT pin, the MCP73830/L is placed in Shutdown
mode.
For a charge cycle to begin, the automatic power-
down conditions must be met, and the charge enable
input must be above the input high threshold. The
battery voltage should be less than 96.5% of V REG .
PRECONDITIONING MODE
If the internal timer expires before the voltage threshold
is reached for Fast Charge mode, a timer fault is
indicated, and the charge cycle terminates. The
MCP73830/L devices remain in this condition until the
battery is removed, the input power is cycled, or CE is
5.2.1
BATTERY MANAGEMENT INPUT
SUPPLY (V DD )
toggled. If the battery is removed, the MCP73830/L
devices enter Standby mode, where they remain until a
battery is reinserted.
The V DD input is the input supply to the MCP73830/L.
The MCP73830/L automatically enters Power-Down
mode if the voltage on the V DD input falls to within
+50 mV of the battery voltage. This feature prevents
draining the battery pack when the V DD supply is not
present.
5.2.2
BATTERY CHARGE CONTROL
OUTPUT (V BAT )
The battery charge control output is the drain terminal
of an internal P-channel MOSFET. The MCP73830/L
provides constant current and voltage regulation to the
battery pack by controlling this MOSFET in the linear
region. The battery charge control output should be
connected to the positive terminal of the battery pack.
? 2011 Microchip Technology Inc.
Note:
The typical preconditioning timers for the
MCP73830/L are 60 minutes. The
MCP73830/L also offers options with no
preconditioning timer.
DS25049B-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| V48C8E150BL | CONVERTER MOD DC/DC 8V 150W |
| H8PPH-1618M | DIP CABLE - HDP16H/AE16M/HDP16H |
| V48C8E150B3 | CONVERTER MOD DC/DC 8V 150W |
| EEV-HA1H100P | CAP ALUM 10UF 50V 20% SMD |
| 342A124-12-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM00317 | 功能描述:数据转换 IC 开发工具 MCP47X6 PICtail Plus Daughter Board RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| ADM00333 | 功能描述:开发板和工具包 - PIC / DSPIC PIC18F87J72 Evaluation Board RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| ADM00344 | 功能描述:电源管理IC开发工具 RE46C190 Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00345 | 功能描述:电源管理IC开发工具 3-Phase BLDC Snsrlss Fan Cntrllr RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00352 | 功能描述:电源管理IC开发工具 MCP16301 600mA Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。