参数资料
| 型号： | ADM00344 |
| 厂商： | Microchip Technology |
| 文件页数： | 13/21页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO EVAL FOR RE46C190 |
| 标准包装： | 1 |
| 主要目的： | 光学烟雾检测器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | RE46C190 |
| 已供物品： | 板，硬件 |
Installation and Operation
Another basic test is the low battery test. Connect a digital multimeter to the test pins
V DD and GND, to monitor the V DD . Toggle the switch SW2 toward the center of the
demo board and observe the change in V DD . Turn Rv2 counterclockwise to lower the
V DD voltage to less than 2.4V, where the low battery threshold should be set. The piezo
horn chirps once every 43 seconds. The low battery Silence mode can be entered by
pressing SW1. Refer to the RE46C190 Data Sheet for details on the Supervisory mode.
The chamber test can be evaluated by first toggling the switch SW2 toward the label
R8 and then turning the 2M POT fully counterclockwise. This places the demo board
in a Non-Alarm state. Short the test point IRED to the test point IRCAP. This disables
the smoke chamber emulator and causes the IC to fail the chamber test. Three chirps
are heard after the test fails. Refer to the RE46C190 Data Sheet for details on this
Supervisory mode.
board. Due to limitations of the smoke emulator, the IRED current, the photo amplifier
gain and the integration time should not be changed.
TABLE 2-1:
PRE-PROGRAMMED RE46C190 SAMPLE
Parameter
Long Term Drift Limit
Chamber Test Limit
Hush Limit
Hysteresis Limit
Normal Smoke Limit
Photo Amplifier Gain Factor
Integration Time
Low Battery Trip Limit
Long Term Drift Enable
Low Battery Hush Enable
IRED Current
Hush Option
End Of Life Enable
Tone Select
Setting
0
2
20
15
20
1
100 μs
2.4V
Disable
Enable
150 mA
Never Cancel
Disabled
Temporal
Chamber Regulator” for details of the connection of the test point. When using the test
points, use an oscilloscope to observe RE46C190’s operation.
? 2011 Microchip Technology Inc.
DS51970A-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| ADM00345 | BOARD DEMO 3PH BLDC CTLR MTD6505 |
| ADM1026EBZEVB | BOARD EVAL FOR ADM1026 |
| ADN8831-EVALZ | BOARD EVAL FOR ADN8831 |
| ADP1043AFB100EVALZ | BOARD EVALUATION ADP1043A 100W |
| ADP1046-100-EVALZ | BOARD EVAL FOR ADP1046-100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM00345 | 功能描述:电源管理IC开发工具 3-Phase BLDC Snsrlss Fan Cntrllr RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00352 | 功能描述:电源管理IC开发工具 MCP16301 600mA Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00360 | 功能描述:电源管理IC开发工具 MCP16301 300mA D2PAK Footprint Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00375 | 功能描述:BOARD EVAL FOR MCP6H04 OP AMP RoHS:否 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ADM00393 | 功能描述:电源管理IC开发工具 64KB Flash, 8KB RAM 16MIPS USBOTG Crypto RoHS:否 制造商:Exar 产品:Evaluation Boards 类型:DC/DC Converters, Regulators & Controllers 工具用于评估:XRP6670 输入电压:2.6 V to 5.5 V 输出电压:0.8 V to 5 V |
发布紧急采购，3分钟左右您将得到回复。