- 您现在的位置：买卖IC网 > PDF目录373995 > ADM1022 (Analog Devices, Inc.) Low-Cost PC Temperature Monitor and Fan Control ASIC PDF资料下载
参数资料
| 型号： | ADM1022 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | Low-Cost PC Temperature Monitor and Fan Control ASIC |
| 中文描述： | 低价电脑温度监控和风扇控制ASIC |
| 文件页数： | 5/19页 |
| 文件大小： | 190K |
| 代理商： | ADM1022 |
REV. 0
ADM1022
–5–
PIN FUNCTION DESCRIPTION
Pin
No.
Mnemonic
Description
1
FAN_OFF
Digital Output (Open-Drain) Fan Off Request. When asserted low this indicates a request to shut
off the fan independent of the FAN_SPD output. When negated (output FET off) it indicates that
the fan may be turned on.
Digital Input, Manual Reset. A logic low on this input causes
RST2
to be asserted. Once this input
is negated that output will remain asserted for t
RP
. This input has an internal 20 k
pull-up resistor.
Leave unconnected if not used.
Digital I/O (Open-Drain). This pin is asserted low while V
CC
remains below the reset threshold. It
remains asserted for t
RP
after the reset condition is terminated. It is bidirectional so the ADM1022 can
be optionally reset; external logic must be used to prevent system auxiliary reset from occurring
when used as an input.
GROUND. Power and Signal Ground.
POWER 3.3 V. Power source and voltage monitor input for first reset generator.
Analog Input. Voltage monitor input for second reset generator.
Digital Output (Open-Drain). This pin is asserted low under any of the following conditions:
– V
MON
or V
CC
remains below the reset threshold
– while
MR
is held low
– while
RST1
is asserted.
It remains asserted for t
RP
after the reset conditions are terminated.
Analog Output/Test Input. An active-high input that enables NAND board-level connectivity testing.
Refer to section on NAND testing. Used as an analog output for fan speed control when NAND
test is not selected.
Remote Thermal Diode Negative Input. This is the negative input (current sink) from the remote
thermal diode. This also serves as the negative input into the A/D.
Remote Thermal Diode Positive Input. This is the positive input (current source) from the remote
thermal diode. This serves as the positive input into the A/D.
Analog Input/Digital I/O (Open-Drain). Can be programmed as negative input for a second diode
temperature sensor, or as a digital I/O pin. In this case it is an active low thermal overload output
that indicates a violation of a temperature set point (over-temperature). Also acts as an input to
provide external fan control. When this pin is pulled low by an external signal, a status bit is set and
the fan speed is set to full on.
Analog/Digital Input. Can be programmed as the positive input for a second diode sensor, or as a
general-purpose logic input. In this case it can be programmed as an active high or active low input
that sets Bit 4 of the Status Registers. This bit can only be reset by reading the status registers, pro-
vided GPI is in the inactive state.
Digital I/O. The lowest order programmable bit of the SMBus Address. ADD is sampled at power-
up and changing it while powered on will have no immediate effect. This pin also functions as an
output when doing a NAND test.
Digital Output (Open Drain), System Interrupt Output. This signal indicates a violation of a set
trip point. The output is enabled when Bit 1 of the Configuration Register is set to 1. The default
state is disabled.
Digital Input SMBus Clock.
Digital I/O (Open-Drain) SMBus Bidirectional Data.
2
MR
3
RST1
4
5
6
7
GND
V
CC
V
MON
RST2
8
FAN_SPD/NTEST_IN
9
D1–
10
D1+
11
D2–/
THERM
12
D2+/GPI
13
ADD/NTEST_OUT
14
INT
15
16
SCL
SDA
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1022ARQ | Low-Cost PC Temperature Monitor and Fan Control ASIC |
| ADM1023 | LJT 6C 6#12 PIN PLUG |
| ADM1023ARQ | ACPI-Compliant High-Accuracy Microprocessor System Temperature Monitor |
| ADM1024 | System Hardware Monitor with Remote Diode Thermal Sensing |
| ADM1024ARU | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM102-22/12VDC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| ADM102-22/24VDC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| ADM102-22/48VDC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| ADM1022ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Analog 16-Pin QSOP 制造商:Rochester Electronics LLC 功能描述:THERMAL MONITOR AND CONTROLER I.C. - Bulk |
| ADM1022ARQ-REEL | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。