- 您现在的位置：买卖IC网 > PDF目录373995 > ADM1024ARU (ANALOG DEVICES INC) Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 PDF资料下载
参数资料
| 型号： | ADM1024ARU |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 电源管理 |
| 英文描述： | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| 中文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封装： | MO-153AD, TSSOP-24 |
| 文件页数： | 12/28页 |
| 文件大小： | 285K |
| 代理商： | ADM1024ARU |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ADM1024
–12–
REV. 0
Register (address 4Bh). As both positive and negative tempera-
tures can be measured, the temperature data is stored in twos
complement format, as shown in Table IV. Theoretically, the
temperature sensor and ADC can measure temperatures from
–128
°
C to +127
°
C with a resolution of 1
°
C, although tempera-
tures below –40
°
C and above +125
°
C are outside the operating
temperature range of the device.
External Temperature Measurement
The ADM1024 can measure the temperature of two external
diode sensors or diode-connected transistors, connected to Pins
13 and 14 or 17 and 18.
Pins 13 and 14 are a dedicated temperature input channel. Pins
17 and 18 can be configured to measure a diode sensor by set-
ting Bit 2 of the Channel Mode Register to 1.
The forward voltage of a diode or diode-connected transistor,
operated at a constant current, exhibits a negative temperature
coefficient of about –2 mV/
°
C. Unfortunately, the absolute value of
V
BE
, varies from device to device, and individual calibration is
required to null this out, so the technique is unsuitable for mass-
production.
The technique used in the ADM1024 is to measure the change
in V
BE
when the device is operated at two different currents.
This is given by:
V
BE
=
KT
/
q
×
ln
(
N
)
where:
K
is Boltzmann’s constant
q
is charge on the carrier
T
is absolute temperature in Kelvins
N
is ratio of the two currents.
Figure 14 shows the input signal conditioning used to measure
the output of an external temperature sensor. This figure shows the
external sensor as a substrate transistor, provided for temperature
monitoring on some microprocessors, but it could equally well
be a discrete transistor.
LOW-PASS
FILTER
f
C
= 65kHz
BIAS
DIODE
REMOTE
SENSING
TRANSISTOR
I
N I
I
BIAS
D+
D
–
V
OUT+
V
OUT
–
TO
ADC
V
DD
Figure 14. Signal Conditioning for External Diode
Temperature Sensors
If a discrete transistor is used, the collector will not be grounded,
and should be linked to the base. If a PNP transistor is used, the
base is connected to the D– input and the emitter to the D+ input.
If an NPN transistor is used, the emitter is connected to the D–
input and the base to the D+ input.
To prevent ground noise from interfering with the measurement,
the more negative terminal of the sensor is not referenced to
ground, but is biased above ground by an internal diode at the
D– input. As the sensor is operating in a noisy environment, C1 is
provided as a noise filter. See the section on layout considerations
for more information on C1.
To measure
V
BE
, the sensor is switched between operating
currents of I and N
×
I. The resulting waveform is passed through
a 65 kHz low-pass filter to remove noise, thence to a chopper-
stabilized amplifier that performs the functions of amplification
and rectification of the waveform to produce a dc voltage pro-
portional to
V
BE
. This voltage is measured by the ADC to give
a temperature output in 8-bit twos complement format. To
further reduce the effects of noise. Digital filtering is performed
by averaging the results of 16 measurement cycles. An external
temperature measurement takes nominally 9.6 ms.
The results of external temperature measurements are stored in
8-bit, twos-complement format, as illustrated in Table IV.
Table IV. Temperature Data Format
Temperature
–128
°
C
–125
°
C
–100
°
C
–75
°
C
–50
°
C
–25
°
C
0
°
C
+0.5
°
C
+10
°
C
+25
°
C
+50
°
C
+75
°
C
+100
°
C
+125
°
C
+127
°
C
Digital Output
1000 0000
1000 0011
1001 1100
1011 0101
1100 1110
1110 0111
0000 0000
0000 0000
0000 1010
0001 1001
0011 0010
0100 1011
0110 0100
0111 1101
0111 1111
LAYOUT CONSIDERATIONS
Digital boards can be electrically noisy environments, and care
must be taken to protect the analog inputs from noise, particularly
when measuring the very small voltages from a remote diode
sensor. The following precautions should be taken:
1. Place the ADM1024 as close as possible to the remote sensing
diode. Provided that the worst noise sources such as clock
generators, data/address buses and CRTs are avoided, this
distance can be 4 to 8 inches.
2. Route the D+ and D– tracks close together, in parallel, with
grounded guard tracks on each side. Provide a ground plane
under the tracks if possible.
3. Use wide tracks to minimize inductance and reduce noise
pickup. Ten mil track minimum width and spacing is
recommended.
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1025 | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025A | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025AARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1025ARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1026 | Complete Thermal and System Management Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1024ARU-REEL | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| ADM1024ARUZ | 功能描述:马达/运动/点火控制器和驱动器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| ADM1024ARUZ-R7 | 功能描述:板上安装温度传感器 +/-2 C / +/-3 C Digital RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL | 功能描述:板上安装温度传感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
发布紧急采购，3分钟左右您将得到回复。