- 您现在的位置：买卖IC网 > PDF目录19409 > ADM1026JSTZ-REEL (ON Semiconductor)IC CTLR SYS REF/EEPROM 48-LQFP PDF资料下载
参数资料
| 型号： | ADM1026JSTZ-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 11/55页 |
| 文件大小： | 0K |
| 描述： | IC CTLR SYS REF/EEPROM 48-LQFP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi |
| 标准包装： | 1 |
| 功能： | 硬件监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 100°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 标准包装 |
| 其它名称： | ADM1026JSTZ-REELOSDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
ADM1026
ADM1026 is powered down, unlike the data in the volatile
registers. Although referred to as read-only memory, the
EEPROM can be written to (as well as read from) via the
serial bus in exactly the same way as the other registers. The
main differences between the EEPROM and other registers
are:
? An EEPROM location must be blank before it can be
written to. If it contains data, it must first be erased.
? Writing to EEPROM is slower than writing to RAM.
? Writing to the EEPROM should be restricted because
its typical cycle life is 100,000 write operations, due to
the usual EEPROM wear-out mechanisms.
Serial Bus Interface
Control of the ADM1026 is carried out via the serial
system management bus (SMBus). The ADM1026 is
connected to this bus as a slave device, under the control of
a master device.
The ADM1026 has a 7-bit serial bus slave address. When
the device is powered on, it does so with a default serial bus
address. The 5 MSBs of the address are set to 01011, and the
2 LSBs are determined by the logical states of Pin 15
ADD/NTESTOUT. This pin is a three-state input that can be
grounded, connected to V CC , or left open-circuit to give
three different addresses.
The EEPROM in the ADM1026 has been qualified for
two key EEPROM memory characteristics: memory cycling
Table 6. ADDRESS PIN TRUTH TABLE
ADD Pin A1
A0
endurance and memory data retention.
Endurance qualifies the ability of the EEPROM to be
cycled through many program, read, and erase cycles. In real
terms, a single endurance cycle is composed of four
GND
No Connect
V CC
0
1
0
0
0
1
independent, sequential events, as follows:
1. Initial page erase sequence
2. Read/verify sequence
3. Program sequence
4. Second read/verify sequence
In reliability qualification, every byte is cycled from 00h
to FFh until a first fail is recorded, signifying the endurance
limit of the EEPROM memory.
Retention quantifies the ability of the memory to retain its
programmed data over time. The EEPROM in the ADM1026
has been qualified in accordance with the formal JEDEC
Retention Lifetime Specification (A117) at a specific junction
temperature (T J = 55 ? C) to guarantee a minimum of 10 years
retention time. As part of this qualification procedure, the
EEPROM memory is cycled to its specified endurance limit
described above before data retention is characterized. This
means that the EEPROM memory is guaranteed to retain its
data for its full specified retention lifetime every time the
EEPROM is reprogrammed. Note that retention lifetime
based on an activation energy of 0.6 V derates with T J , as
shown in Figure 15.
300
250
200
150
100
50
If ADD is left open-circuit, the default address is 0101110
(5Ch). ADD is sampled only at powerup on the first valid
SMBus transaction, so any changes made while the power
is on (and the address is locked) have no effect.
The facility to make hardwired changes to device
addresses allows the user to avoid conflicts with other
devices sharing the same serial bus, for example if more than
one ADM1026 is used in a system.
General SMBus Timing
Figure 16 and Figure 17 show timing diagrams for general
read and write operations using the SMBus. The SMBus
specification defines specific conditions for different types
of read and write operations, which are discussed later in this
section. The general SMBus protocol * operates as follows:
1. The master initiates data transfer by establishing a
start condition, defined as a high-to-low transition
on the serial data line (SDA) while the serial clock
line SCL remains high. This indicates that a data
stream follows. All slave peripherals connected to
the serial bus respond to the start condition and
shift in the next 8 bits, consisting of a 7-bit slave
address (MSB first) and an R/W bit, which
determine the direction of the data transfer, that is,
whether data is written to or read from the slave
device (0 = write, 1 = read).
The peripheral whose address corresponds to the
trans-mitted address responds by pulling the data
line low during the low period before the ninth
clock pulse, known as the acknowledge bit, and
holding it low during the high period of this clock
pulse. All other devices on the bus remain idle
while the selected device waits for data to be read
from or written to it. If the R/W bit is 0, the master
0
40
50
60 70 80 90 100
JUNCTION TEMPERATURE ( 5 C)
110
120
writes to the slave device. If the R/W bit is 1, the
master reads from the slave device.
Figure 15. Typical EEPROM Memory Retention
http://onsemi.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| ECC06DRXH | CONN EDGECARD 12POS DIP .100 SLD |
| ASM28DSEF-S243 | CONN EDGECARD 56POS .156 EYELET |
| TAJX337M004RNJ | CAP TANT 330UF 4V 20% 2917 |
| GCM11DSEH | CONN EDGECARD 22POS .156 EYELET |
| EEC06DRAS | CONN EDGECARD 12POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1026JSTZ-REEL7 | 制造商:Analog Devices 功能描述:IC SYSTEM MONITOR 制造商:ON Semiconductor 功能描述:IC SYSTEM MONITOR |
| ADM1027 | 制造商:AD 制造商全称:Analog Devices 功能描述:dBCOOL-TM Remote Thermal Controller and Voltage Monitor |
| ADM1027ARQ | 功能描述:IC THER CTRL VOLT/MONITOR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1027ARQ-REEL | 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1027ARQ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。