- 您现在的位置：买卖IC网 > PDF目录22030 > ADM1027ARQZ (ON Semiconductor)IC THER CTRL VOLT/MONITOR 24QSOP PDF资料下载
参数资料
| 型号： | ADM1027ARQZ |
| 厂商： | ON Semiconductor |
| 文件页数： | 19/56页 |
| 文件大小： | 1822K |
| 描述： | IC THER CTRL VOLT/MONITOR 24QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation Notice 25/Aug/2008 Product Obsolescence 30/Sept/2009 |
| 标准包装： | 56 |
| 系列： | dBCool® |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 105°C，外部传感器 |
| 精确度： | ±1°C |
| 拓扑： | ADC，比较器，风扇速度计数器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
REV. A
ADM1027
19
SMBALERT INTERRUPT BEHAVIOR
The ADM1027 can be polled for status, or an SMBALERT
interrupt can be generated for out-of-limit conditions. It is
important to note how the SMBALERT output and status bits
behave when writing interrupt handler software.
STICKY
STATUS
BIT
HIGH LIMIT
TEMPERATURE
SMBALERT
CLEARED ON READ
(TEMP BELOW LIMIT)
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
Figure 16. SMBALERT and Status Bit Behavior
Figure 16 shows how the SMBALERT output and sticky status
bits behave. Once a limit is exceeded, the corresponding status
bit is set to 1. The status bit remains set until the error condition
subsides and the status register is read. The status bits are referred
to as sticky since they remain set until read by software. This
ensures that an out-of-limit event cannot be missed if software
is polling the device periodically. Note that the SMBALERT
output remains low for the entire duration that a reading is
out-of-limit and until the status register has been read. This has
implications on how software handles the interrupt.
HANDLING SMBALERT INTERRUPTS
To prevent the system from being tied up servicing interrupts,
it is recommend to handle the SMBALERT interrupt as follows:
1. Detect the SMBALERT assertion.
2. Enter the interrupt handler.
3. Read the status registers to identify the interrupt source.
4. Mask the interrupt source by setting the appropriate mask bit
in the interrupt mask registers (Reg. 0x74, 0x75).
5. Take the appropriate action for a given interrupt source.
6. Exit the interrupt handler.
7. Periodically poll the status registers. If the interrupt status bit
has cleared, reset the corresponding interrupt mask bit to 0.
This will cause the SMBALERT output and status bits to
behave as shown in Figure 17.
STICKY
STATUS
BIT
HIGH LIMIT
TEMPERATURE
SMBALERT
CLEARED ON READ
(TEMP BELOW LIMIT)
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
INTERRUPT
MASK BIT SET
INTERRUPT MASK
BIT CLEARED
(SMBALERT REARMED)
Figure 17. How Masking the Interrupt Source
Affects SMBALERT Output
MASKING INTERRUPT SOURCES
Interrupt Mask Registers 1 and 2 are located at Addresses 0x74
and 0x75. These allow individual interrupt sources to be masked
out to prevent SMBALERT interrupts. Note that masking an
interrupt source prevents only the SMBALERT output from
being asserted; the appropriate status bit will be set as normal.
INTERRUPT MASK REGISTER 1 (REG. 0x74)
Bit 7 (OOL) = 1, set this bit to 1 to allow masking of interrupts
by Status Register 2. If this bit = 0, then setting a bit in Mask
Register 2 to 1 will have no effect.
Bit 6 (R2T) = 1, masks SMBALERT for Remote 2 temperature.
Bit 5 (LT) = 1, masks SMBALERT for local temperature.
Bit 4 (R1T) = 1, masks SMBALERT for Remote 1 temperature.
Bit 3 (5 V) = 1, masks SMBALERT for 5 V channel.
Bit 2 (V
CC
) = 1, masks SMBALERT for V
CC
channel.
Bit 1 (V
CCP
) = 1, masks SMBALERT for V
CCP
channel.
Bit 0 (2.5 V) = 1, masks SMBALERT for 2.5 V channel.
INTERRUPT MASK REGISTER 2 (REG. 0x75)
Bit 7 (D2) = 1, masks SMBALERT for Diode 2 errors.
Bit 6 (D1) = 1, masks SMBALERT for Diode 1 errors.
Bit 5 (FAN4) = 1, masks SMBALERT for Fan 4.
Bit 4 (FAN3) = 1, masks SMBALERT for Fan 3.
Bit 3 (FAN2) = 1, masks SMBALERT for Fan 2.
Bit 2 (FAN1) = 1, masks SMBALERT for Fan 1.
Bit 1 (OVT) = 1, masks SMBALERT for overtemperature
(exceeding THERM limits).
Bit 0 (12 V) = 1, masks SMBALERT for 12 V channel.
Rev. 3 | Page 19 of 56 | www.onsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BW4-CV-F4 | CONVERTER MOD DC/DC 48V 150W |
| VE-BW4-CV-F3 | CONVERTER MOD DC/DC 48V 150W |
| ADM1026JSTZ | IC CNTRL SYS REF/EEPROM 48LQFP |
| ICD15S13E4GX00LF | CONN DSUB RCPT 15POS T/H RA GOLD |
| ADM1033ARQ | IC THERM/FAN SPEED CTRLR 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1027ARQZ-REEL | 功能描述:板上安装温度传感器 VOLT THRM MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1027ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1027ARQZ-RL7 | 功能描述:IC REMOTE THERMAL CTLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1027ARQZ-RL71 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:dBCOOLa?￠ Remote Thermal Controller and Voltage Monitor |
| ADM1028 | 制造商:AD 制造商全称:Analog Devices 功能描述:Remote Thermal Diode Monitor with Linear Fan Control |
发布紧急采购，3分钟左右您将得到回复。