- 您现在的位置：买卖IC网 > Datasheet目录39 > ADM1030ARQZ-RL7 (ON Semiconductor)IC SNSR TEMP/FAN PWM CTRL 16QSOP Datasheet资料下载
参数资料
| 型号： | ADM1030ARQZ-RL7 |
| 厂商： | ON Semiconductor |
| 文件页数： | 25/30页 |
| 文件大小： | 327K |
| 描述： | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 11/Feb/2009 |
| 标准包装： | 1,000 |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 100°C，外部传感器 |
| 精确度： | ±1°C，±1°C（最小值） |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页
ADM1030
http://onsemi.com
25
Table 17. VALUE AND LIMIT REGISTERS
Address
Read/Write
Description
0x06
Read/Only
Extended Temperature Resolution (see Table 22).
0x08
Read/Write
Fan Speed Reading this register contains the fan speed tach measurement.
0x0A
Read/Only
Local Temperature Value this register contains the 8 MSBs of the local temperature measurement.
0x0B
Read/Only
Remote Temperature Value this register contains the 8 MSBs of the remote temperature reading.
0x0D
Read/Write
Local Temperature Offset See Table 29.
0x0E
Read/Write
Remote Temperature Offset See Table 30.
0x10
Read/Write
Fan Tach High Limit this register contains the limit for the fan tach measurement. Since the tach
circuit counts between pulses, a slow fan will result in a large measured value, so exceeding the limit
by one is the way to detect a slow or stalled fan. (Power-on Default = FFh)
0x14
Read/Write
Local Temperature High Limit (Power-on Default 60rC).
0x15
Read/Write
Local Temperature Low Limit (Power-on Default 0rC).
0x16
Read/Write
Local Temperature Therm Limit (Power-on Default 70rC).
0x18
Read/Write
Remote Temperature High Limit (Power-on Default 80rC).
0x19
Read/Write
Remote Temperature Low Limit (Power-on Default 0rC).
0x1A
Read/Write
Remote Temperature Therm Limit (Power-on Default 100rC).
Table 18. REGISTER 0X00 CONFIGURATION REGISTER 1 POWER-ON DEFAULT 90H
Bit
Name
R/W
Description
0
MONITOR
Read/Write
Setting this bit to a 1 enables monitoring of temperature and enables measurement of
the fan tach signals. (Power-up Default = 0)
1
INT
Enable
Read/Write
Setting this bit to a 1 enables the INT
output. 1 = Enabled 0 = Disabled (Power-up
Default = 0)
2
TACH/AIN
Read/Write
Clearing this bit to 0 selects digital fan speed measurement via the TACH pins. Setting
this bit to 1 configures the TACH pins as analog inputs that can measure the speed of
2-wire fans via a sense resistor. (Power-up Default = 0)
3
PWM Invert
Read/Write
Setting this bit to 1 inverts the PWM signal on the output pin. (Power-up Default = 0).
The power-up default makes the PWM_OUT pin go low for 100% duty cycle (suitable
for driving the fan using a PMOS device). Setting this bit to 1 makes the PWM_OUT
pin high for 100% duty cycle (intended for driving the fan using an NMOS device).
4
Fan Fault Enable
Read/Write
Logic 1 enables FAN_FAULT
pin; Logic 0 disables FAN_FAULT
output. (Power-up
Default = 1.)
65
PWM Mode
Read/Write
These two bits control the behavior of the fan in Auto Fan Speed Control Mode.
00 = Remote Temp controls Fan. (Program PWM duty cycle in Software Mode.)
11 = Fastest Calculated Speed Controls Fan. (Program RPM speed in Software Mode.)
7
Auto/SW Ctrl
Read/Write
Logic 1 selects Automatic Fan Speed Control; Logic 0 selects SW control. (Power-up
Default = 1) When under software control, PWM duty cycle or RPM values may be
programmed for the fan.
Table 19. REGISTER 0X01 CONFIGURATION 2 POWER-ON DEFAULT = 7FH
Bit
Name
R/W
Description
0
PWM 1 En
Read/Write
Enables fan PWM output when this bit is a 1.
1
Unused
Read/Write
Unused
2
TACH 1 En
Read/Write
Enables Tach input when set to 1.
3
Unused
4
Loc Temp En
Read/Write
Enables Interrupts on Local Channel when set to 1.
5
Remote Temp En
Read/Write
Enables Interrupts on Remote Channel when set to 1. Default is normally enabled,
except when a diode fault is detected on power-up.
6
Unused
Read/Write
Unused
7
SW Reset
Read/Write
When set to 1, resets the device. Self-clears. Power-up Default = 0.
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
| ADN8810ACPZ-REEL7 | IC CURRENT SOURCE(12BIT) 24LFCSP |
| ADP2140ACPZ3328R7 | IC REG DL BCK/LINEAR 10LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1031 | 制造商:AD 制造商全称:Analog Devices 功能描述:Intelligent Temperature Monitor and Dual PWM Fan Controller |
| ADM1031ARQ | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1031ARQ-ND | 制造商:ON Semiconductor 功能描述: |
| ADM1031ARQ-REEL | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1031ARQ-REEL7 | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。