- 您现在的位置：买卖IC网 > PDF目录22039 > ADM1031ARQ-REEL (ON Semiconductor)IC SENSOR 2-TEMP/FAN CTRL 16QSOP PDF资料下载
参数资料
| 型号： | ADM1031ARQ-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR 2-TEMP/FAN CTRL 16QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi LTB Notification |
| 标准包装： | 2,500 |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 100°C，外部传感器 |
| 精确度： | ±1°C 本地，±0.5°C 远程 |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1031
speed up due to aging, the RPM feedback slows the fan down
to maintain the correct RPM speed. The value to be
programmed into each fan tach high limit register is given by:
Once the count value has been calculated, it should be
written to the fan tach high limit register. It should be noted
that in RPM feedback mode, there is no high limit register
Count + (f 60) R N
where:
f = 11.25 kHz
R = desired RPM value
N = Speed Range; MUST be set to 2
(eq. 7)
for underspeed detection that can be programmed as there
are in the other fan speed control modes. The only time each
fan indicates a fan failure condition is whenever the count
reaches 255. Since the speed range N = 2, the fan fails if its
speed drops below 1324 RPM.
The speed range, N, really determines what the slowest
fan speed measured can be before generating an interrupt.
The slowest fan speed is measured when the count value
reaches 255.
Since N = 2
Count + (f 60) R N
R + (f 60) Count N
R + (11250 60) 255 2 (eq. 8)
R + (675000) 510
R + 1324 RPM, fan fail detect speed.
Programming RPM Values in RPM Feedback Mode
Rather than writing a value such as 5000 to a 16-bit
register, an 8-bit count value is programmed instead. The
Programming RPM Values
1. Choose the RPM value to be programmed.
2. Set speed range value N = 2.
3. Calculate count value based on RPM and speed
range values chosen. Use the count equation to
calculate the count value.
4. Clear Bit 7 of Configuration Register 1
(Register 0 ? 00) to place the ADM1031 under
software control.
5. Write a 1 to Bit 5 of Configuration Register 1 to
place the device in RPM feedback mode.
6. Write the calculated count value to the fan tach
high limit register (Register 0 ? 10). The fan speed
now goes to the desired RPM value and maintains
that fan speed.
count to be programmed is given by:
Count + (f 60) R N
(eq. 9)
RPM Feedback Mode Limitations
RPM feedback mode only controls fan RPM over a limited
where:
f = 11.25 kHz
R = desired RPM value
N = Speed Range = 2
Example 1:
If the desired value for RPM feedback mode is 5000 RPM,
the count to be programmed is:
Count + (f 60) R N (eq. 10)
Since the desired RPM value, R is 5000 RPM, the value
for count is:
N = 2:
Count + (11250 60) 5000 2
Count + 675000 10000 (eq. 11)
Count + 67 (assumes 2 tach pulses rev).
Example 2:
If the desired value for RPM feedback mode is 3650 RPM,
the count to be programmed is:
Count + (f 60) R N (eq. 12)
Since the desired RPM value, R is 3650 RPM, the value
for count is:
fan speed range of about 75% to 100%. However, this should
be enough range to overcome fan-manufacturing tolerance.
In practice, however, the program must not function at too
low an RPM value for the fan to run at, or the RPM mode does
not operate.
To find the lowest RPM value allowed for a given fan, do
the following:
1. Run the fan at 53% PWM duty cycle in software
mode. Clear Bit 5 and Bit 7 of Configuration
Register 1 (Register 0 ? 00) to enter PWM duty
cycle mode. Write 0 ? 08 to the fan speed
configuration register (Register 0 ? 22) to set the
PWM output to 53% duty cycle.
2. Measure the fan RPM. This represents the fan
RPM below which the RPM mode fails to operate.
Do not program a lower RPM than this value when
using RPM feedback mode.
3. Ensure that speed range N = 2 when using RPM
feedback mode.
Fan Drive and Speed Measurement
Fans come in a variety of different options. One
distinguishing feature of fans is the number of poles that a
N = 2:
Count + (11250 60) 3650 2
Count + 675000 7300
Count + 92 (assumes 2 tach pulses rev).
(eq. 13)
fan has internally. The most common fans available have
four, six, or eight poles. The number of poles the fan has
generally affects the number of pulses per revolution the fan
outputs.
If the ADM1031 is used to drive fans other than 4-pole
fans that output 2 tach pulses/revolution, then the fan speed
measurement equation needs to be adjusted to calculate and
http://onsemi.com
21
相关PDF资料 |
PDF描述 |
|---|---|
| AGL030V2-UCG81 | IC FPGA IGLOO 1.2-1.5V UCG81 |
| AMC22DRES-S93 | CONN EDGECARD 44POS .100 EYELET |
| AGL030V2-VQG100 | IC FPGA IGLOO 1.2-1.5V 100VQFP |
| ADM1031ARQ | IC SENSOR 2-TEMP/FAN CTRL 16QSOP |
| GSC49DRTI-S734 | CONN EDGECARD 98POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1031ARQ-REEL7 | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1031ARQZ | 功能描述:马达/运动/点火控制器和驱动器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| ADM1031ARQZ-R7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1031ARQZ-REEL | 功能描述:板上安装温度传感器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1031ARQZ-REEL7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。