- 您现在的位置：买卖IC网 > PDF目录67357 > ADM1031ARQZ-R7 (ON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | ADM1031ARQZ-R7 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封装： | LEAD FREE, QSOP-16 |
| 文件页数： | 29/30页 |
| 文件大小： | 299K |
| 代理商： | ADM1031ARQZ-R7 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页
ADM1031
http://onsemi.com
8
during the high period, as a lowtohigh transition
when the clock is high can be interpreted as a stop
signal. The number of data bytes that can be
transmitted over the serial bus in a single read or
write operation is limited only by what the master
and slave devices can handle.
3. When all data bytes have been read or written,
stop conditions are established. In write mode, the
master pulls the data line high during the tenth
clock pulse to assert a stop condition. In read
mode, the master device overrides the
acknowledge bit by pulling the data line high
during the low period before the ninth clock pulse.
This is known as No Acknowledge. The master
then takes the data line low during the low period
before the tenth clock pulse, then high during the
tenth clock pulse to assert a stop condition.
Any number of bytes of data can be transferred over the
serial bus in one operation, but it is not possible to mix read
and write in one operation, because the type of operation is
determined at the beginning and cannot subsequently be
changed without starting a new operation.
In the case of the ADM1031, write operations contain
either one byte or two bytes, and read operations contain one
byte, and perform the functions described next.
Writing Data to a Register
To write data to one of the device data registers or read
data from it, the address pointer register must be set so that
the correct data register is addressed; data can then be
written to that register or read from it. The first byte of a
write operation always contains an address that is stored in
the address pointer register. If data is to be written to the
device, the write operation contains a second data byte that
is written to the register selected by the address pointer
register.
This is illustrated in Figure 15. The device address is sent
over the bus followed by R/W set to 0. This is followed by
two data bytes. The first data byte is the address of the
internal data register to be written to, which is stored in the
address pointer register. The second data byte is the data to
be written to the internal data register.
Reading Data from a Register
When reading data from a register there are two
possibilities:
1. If the ADM1031’s address pointer register value is
unknown or not the desired value, it is first
necessary to set it to the correct value before data
can be read from the desired data register. This is
done by performing a write to the ADM1031 as
before, but only the data byte containing the
register address is sent, as data is not to be written
to the register. This is shown in Figure 16.
A read operation is then performed consisting of
the serial bus address, R/W bit set to 1, followed
by the data byte read from the data register. This is
shown in Figure 17.
2. If the address pointer register is known to be
already at the desired address, data can be read
from the corresponding data register without first
writing to the address pointer register, so Figure 16
can be omitted.
Notes
Although it is possible to read a data byte from a data
register without first writing to the address pointer
register, if the address pointer register is already at the
correct value, it is not possible to write data to a register
without writing to the address pointer register. This is
because the first data byte of a write is always written
to the address pointer register.
In Figure 15, Figure 16, and Figure 17, the serial bus
address is shown as the default value 01011(A1)(A0),
where A1 and A0 are set by the threestate ADD pin.
The ADM1031 also supports the Read Byte protocol, as
described in the system management bus specification.
Figure 15. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register
START BY
MASTER
STOP BY
MASTER
ACK. BY
ADM1031
ACK. BY
ADM1031
ACK. BY
ADM1031
0
11
9
1
0
1
A1
A0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
SCL
SDA
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
FRAME 3
DATA BYTE
SDA (CONTINUED)
SCL (CONTINUED)
9
1
D7
D6
D5
D4
D3
D2
D1
D0
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1031ARQZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADM1031ARQZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADM1031ARQZ | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADM1031ARQ | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADRF6604ACPZ-R7 | 2500 MHz - 2900 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1031ARQZ-REEL | 功能描述:板上安装温度传感器 2 CH TDM PWM FAN CTRL IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1031ARQZ-REEL7 | 功能描述:IC SENSOR 2TEMP/FAN CTRL 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1032 | 制造商:AD 制造商全称:Analog Devices 功能描述:+-1C Remote and Local System Temperature Monitor |
| ADM1032_12 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1C Remote and Local System Temperature Monitor Supports SMBus Alert |
| ADM1032AR | 功能描述:IC TEMP MONITOR 85DEG C 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。