- 您现在的位置：买卖IC网 > PDF目录22012 > ADM1032ARMZ-R7 (ON Semiconductor)IC TEMP MONITOR 85DEG 8MSOP PDF资料下载
参数资料
| 型号： | ADM1032ARMZ-R7 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/18页 |
| 文件大小： | 197K |
| 描述： | IC TEMP MONITOR 85DEG 8MSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation 30/Sept/2011 |
| 标准包装： | 1,000 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 120°C |
| 精确度： | ±3°C |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | 2 线 SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 120°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | Micro8? |
| 包装： | 带卷 (TR) |
ADM1032
http://onsemi.com
7
Functional Description
The ADM1032 is a local and remote temperature sensor
and overtemperature alarm. When the ADM1032 is
operating normally, the on-board A/D converter operates in
a free running mode. The analog input multiplexer
alternately selects either the on-chip temperature sensor to
measure its local temperature or the remote temperature
sensor. These signals are digitized by the ADC, and the
results are stored in the local and remote temperature value
registers.
The measurement results are compared with local and
remote, high, low, and THERM
temperature limits stored in
nine on-chip registers. Out-of-limit comparisons generate
flags that are stored in the status register, and one or more
out-of-limit results cause the ALERT
output to pull low.
Exceeding THERM
temperature limits causes the THERM
output to assert low.
The limit registers can be programmed, and the device
controlled and configured, via the serial SMBus. The
contents of any register can also be read back via the SMBus.
Control and configuration functions consist of:
" Switching the Device between Normal Operation and
Standby Mode
" Masking or Enabling the ALERT
Output
" Selecting the Conversion Rate
Measurement Method
A simple method of measuring temperature is to exploit
the negative temperature coefficient of a diode, or the
base-emitter voltage of a transistor, operated at constant
current. Unfortunately, this technique requires calibration to
null out the effect of the absolute value of V
BE
, which varies
from device to device.
The technique used in the ADM1032 is to measure the
change in V
BE
when the device is operated at two different
currents.
This is given by:
(eq. 1)
DV
BE
+
n
f
KT
q
In
(
N
)
where:
K is Boltzmanns constant (1.38 ?/SPAN> 10
23
)
q is the charge on the electron (1.6 ?/SPAN> 10
19
Coulombs)
T is the absolute temperature in Kelvins
N is the ratio of the two currents
n
f
is the ideality factor of the thermal diode.
The ADM1032 is trimmed for an ideality factor of 1.008.
Figure 12 shows the input signal conditioning used to
measure the output of an external temperature sensor.
Figure 12 shows the external sensor as a substrate transistor,
provided for temperature monitoring on some
microprocessors, but it could equally well be a discrete
transistor. If a discrete transistor is used, the collector is not
grounded and should be linked to the base. To prevent
ground noise interfering with the measurement, the more
negative terminal of the sensor is not referenced to ground
but is biased above ground by an internal diode at the D
input. If the sensor is operating in a noisy environment, C1
can optionally be added as a noise filter. Its value should be
no more than 1000 pF. See the Layout Considerations
section for more information on C1.
To measure DV
BE
, the sensor is switched between the
operating currents of I and N ?I. The resulting waveform is
passed through a 65 kHz low-pass filter to remove noise, and
then to a chopper-stabilized amplifier that performs the
functions of amplification and rectification of the waveform
to produce a dc voltage proportional to DV
BE
. This voltage
is measured by the ADC to give a temperature output in twos
complement format. To further reduce the effects of noise,
digital filtering is performed by averaging the results of 16
measurement cycles.
Signal conditioning and measurement of the internal
temperature sensor is performed in a similar manner.
Figure 12. Input Signal Conditioning
LOW-PASS FILTER
f
C
= 65 kHz
REMOTE
SENSING
TRANSISTOR
BIAS
DIODE
D+
D
V
DD
I
BIAS
I
N ?I
V
OUT+
V
OUT
To ADC
C1*
* CAPACITOR C1 IS OPTIONAL AND IT SHOULD ONLY BE USED IN VERY NOISY ENVIRONMENTS. C1 = 1000 pF Max.
相关PDF资料 |
PDF描述 |
|---|---|
| EP4CGX22CF19C7N | IC CYCLONE IV FPGA 22K 324-FBGA |
| EYM15DRMD | CONN EDGECARD 30POS .156 WW |
| BAT54T1G | DIODE SCHOTTKY DET/SW 30V SOD123 |
| VI-BNJ-CX | CONVERTER MOD DC/DC 36V 75W |
| AIMC-0603-4N7S-T | INDUCTOR MULTILAYER 4.7NH 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1032ARMZREEL | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1C Remote and Local System Temperature Monitor |
| ADM1032ARMZ-REEL | 功能描述:板上安装温度传感器 8-PIN TDM RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1032ARMZ-REEL7 | 功能描述:IC TEMP MONITOR 85DEG 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1032AR-REEL | 功能描述:IC TEMP MONITOR 85DEF 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1032AR-REEL7 | 功能描述:IC TEMP MONITOR 85DEF 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。