- 您现在的位置：买卖IC网 > PDF目录22031 > ADM1034ARQ-REEL (ON Semiconductor)IC THERM/FAN SPEED CTRLR 16-QSOP PDF资料下载
参数资料
| 型号： | ADM1034ARQ-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 23/38页 |
| 文件大小： | 427K |
| 描述： | IC THERM/FAN SPEED CTRLR 16-QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 30/Sept/2009 |
| 标准包装： | 2,500 |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C，外部传感器 |
| 精确度： | ±1°C |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
ADM1034
http://onsemi.com
23
R1 and R2 should be chosen such that
(eq. 3)
2V t V
PULLUP
R2(R
PULLUP
) R1 ) R2) t 5 V
The fan inputs have an input resistance of nominally
160 kW to ground. This should be taken into account when
calculating resistor values.
With a pullup voltage of 12 V and pullup resistor less than
1 kW, suitable values for R1 and R2 would be 100 kW and
47 kW. This gives a high input voltage of 3.83 V.
Figure 37. Fan with Strong TACH. Pullup to >V
CC
or
Totem-Pole Output, Clamped with Zener and Resistor
12 V
V
CC
FAN SPEED
COUNTER
FAN (07)
ADM1034
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 ?V
CC
PULLUP
TYP < 1 kW
OR TOTEM-POLE
ZD1*
Figure 38. Fan with Strong TACH. Pullup to >V
CC
or
Totem-Pole Output, Attenuated with R1/R2
12 V
V
CC
FAN SPEED
COUNTER
FAN (07)
ADM1034
*SEE TEXT
< 1 kW
R1*
R2
TACH
OUTPUT
Fan Speed Measurement
The fan counter does not count the fan TACH output
pulses directly. This is because the fan may be spinning at
less than 1000 rpm and it would take several seconds to
accumulate a reasonably large and accurate count. Instead,
the period of the fan revolution is measured by gating an
on-chip 81.92 kHz oscillator into the input of a 16-bit
counter for one complete revolution of the fan. Therefore,
the accumulated count is actually proportional to the fan
tachometer period and inversely proportional to the fan
speed.
The number of poles in the fan must be programmed in
Configuration Register 3 (Address 0x03). Bits <3:0> set the
number of poles for Fan 1, and Bits <7:4> set the number of
poles for Fan 2. This number must be an even number only,
because there cannot be an uneven number of poles in a fan.
A TACH period is output for every two poles. Therefore, the
number of poles must be known so that the ADM1034 can
measure for a full revolution.
Figure 39 shows the fan speed measurement period,
assuming that the fan outputs an ideal TACH signal. In
reality, the TACH signal output by the fan is chopped by the
drive signal. However, since the drive and the TACH signal
are synchronized, there is enough information available for
the ADM1034 to measure the fan speed accurately.
Figure 39. Fan Speed Measurement for a 4-pole Fan
CLOCK
IDEAL
TACH
FAN
MEASUREMENT
PERIOD
Fan Speed Measurement Registers
These 16-bit measurements are stored in the TACH value
registers.
Table 26. TACH VALUE REGISTERS
Register
Description
Default
0x4A
TACH1 Period, LSB
0xFF
0x4B
TACH1 Period, MSB
0xFF
0x4C
TACH2 Period, LSB
0xFF
0x4D
TACH2 Period, MSB
0xFF
Reading Fan Speed
Reading back fan speeds involves a 2-register read for
each measurement. The low byte should be read first. This
freezes the high byte until both high and low byte registers
have been read, preventing erroneous fan speed
measurement readings.
The fan tachometer reading registers report back the
number of 12.2 ms period clocks (81.92 kHz oscillator)
gated to the fan speed counter, for one full rotation of the fan,
assuming the correct number of poles is programmed. Since
the ADM1034 essentially measures the fan TACH period,
the higher the count value, the slower the actual fan speed.
A 16-bit fan TACH reading of 0xFFFF indicates that the fan
has stalled or is running very slowly (< 75 rpm).
Calculating Fan Speed
Fan speed in rpm is calculated as follows. This assumes
that the number of poles programmed in the Configuration
Register 3 (Address 0x03) is correct for both fans.
Fan Speed (RPM) = (81920 ?60)/Fan TACH Reading
where:
Fan TACH Reading = 16-bit Fan TACHometer Reading
Example:
TACH1 High Byte (Reg. 0x4A) = 0x17
TACH1 Low Byte (Reg. 0x4B) = 0xFF
What is Fan 1 speed in rpm?
Fan 1 TACH Reading = 0x17FF = 6143d
RPM = (f ?60) / Fan 1 TACH reading
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2WJ-CW-F1 | CONVERTER MOD DC/DC 36V 100W |
| VE-2WH-CW-F4 | CONVERTER MOD DC/DC 52V 100W |
| ADT7468ARQ-REEL7 | IC REMOTE THERMAL CTRLR 24-QSOP |
| EPF6016ATC100-3N | IC FLEX 6000 FPGA 16K 100-TQFP |
| ADT7468ARQ-REEL | IC REMOTE THERMAL CTRLR 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1034ARQ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1034ARQZ | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1034ARQZ-R7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1034ARQZ-REEL | 功能描述:板上安装温度传感器 2 FAN CTRLR SRC SMBUS IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1034ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。