- 您现在的位置：买卖IC网 > PDF目录373995 > ADM1041 (Analog Devices, Inc.) Secondary-Side Controller with Current Share and Housekeeping PDF资料下载
参数资料
| 型号： | ADM1041 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | Secondary-Side Controller with Current Share and Housekeeping |
| 中文描述： | 二次侧电流控制器共享和管家 |
| 文件页数： | 28/64页 |
| 文件大小： | 1063K |
| 代理商： | ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
ADM1041
OrFET GATE DRIVE
When configured, this block provides a signal to turn on/off an
OrFET used in the output of paralleled power supplies. The gate
drive voltage of one of these FETs is typically 6 V to 10 V above
the output voltage. Since the output voltage of the ADM1041 is
limited, an external transistor needs to be used. The block
diagram shows an example of this approach. See Figure 21.
Rev. A | Page 28 of 64
The F
G
output is an open-drain, N-channel MOSFET and is
normally high, which holds the OrFET off. When all the start-
up conditions are correct, Pin 19 is pulled low, which allows the
OrFET to turn on. The logic can also be configured as inverted
if a noninverting drive circuit is used.
A differential amplifier monitors the voltage across the OrFET
and has two major functions. First, during start-up, it allows the
OrFET to turn on with almost 0 V across it to avoid voltage
glitches on the bus. This applies to a hot bus or a cold bus. The
internal threshold can be configured from 20 mV to 50 mV
(negative), which is scaled up by the external voltage dividers.
Second, if a rectifier or filter capacitor fails during steady state
operation, it detects the resulting reverse voltage across the
OrFET’s on-resistance and turns off the OrFET before a voltage
dip appears on the bus. The internal threshold can be configured
from 100 mV to 250 mV (negative), which is also scaled up by
the external voltage dividers. A slightly larger filter capacitor
may be used on the voltage divider at Pin 6 to speed up this
function.
Figure 17 shows the typical response time of the ADM1041 to
such an event. In the plot, V
FD
is ramped down and the response
time of the F
G
pin to a reverse voltage event on the F
D
pin is
seen. This simulates the rectifier or filter capacitor failure
during steady state operation. When the F
D
voltage is below
1.9 V (2 V minus 100 mV threshold), the F
G
pin reacts. As can
be seen, the response time is approx 330 nsecs. This extremely
fast turn-off is vital in an n+1 power supply system configuration.
It ensures that the damaged power supply removes itself from
the system quickly. Figure 18 is the equivalent response time to
turn on the OrFET. As can be seen, there is a delay of approxi-
mately 500 ns before the FG pin ramps down to turn on the
OrFET, and therefore allow the power supply to contribute to the
system. This propagation delay is due mainly to internal amplifier
response limitations. The circuit in Figure 21 is used to generate
these plots. In this case, the resistor to VDD from the FG pin is
2 k.
Figure 19 and Figure 20 show the OrFET turn-off time and
turn-on time when the F
G
pin polarity is inverted. As can be
seen, to turn off the OrFET, the V
FG
pin now transitions from
high to low. Also, its corresponding turn-on event occurs from a
low-to-high transition. The circuit in Figure 21 is used to
generate these plots.
0
64%
T
TOTAL
= 330ns
T
DELAY
= 218ns T = 112ns
Figure 17. OrFET Turn-Off Time (Default Polarity)
T
TOTAL
= 506ns
0
Figure 18. OrFET Turn-On Time (Default Polarity)
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041A | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
发布紧急采购，3分钟左右您将得到回复。