- 您现在的位置：买卖IC网 > PDF目录15310 > ADM1060ARU-REEL (Analog Devices Inc)IC SUPERVISOR/SEQUENCER 28TSSOP PDF资料下载
参数资料
| 型号： | ADM1060ARU-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/52页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR/SEQUENCER 28TSSOP |
| 标准包装： | 2,500 |
| 系列： | Super Sequencer® |
| 类型： | 序列发生器 |
| 监视电压数目： | 7 |
| 输出： | 可编程 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-ADM1060EBZ-ND - BOARD EVALUATION ADM1060 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADM1060
INPUTS
VH
POWERING THE ADM1060
The ADM1060 is powered from the highest voltage input on
either the Positive Only supply inputs (VPn) or the High Volt-
age supply input (VH). The same pins are used for supply fault
detection (discussed below). A V DD arbitrator on the device
chooses which supply to use. The arbitrator can be considered
VDDCAP PIN
as diode OR’ing the positive supplies together (as shown in
Figure 17).The diodes are supplemented with switches in a syn-
chronous rectifier manner to minimize voltage loss. This loss
can be reduced to ~0.2 V, resulting in the ability to power the
ADM1060 from a supply as low as 3.0 V. Note that the supply on
the VBn pins cannot be used to power the device, even if the
input on these pins is positive. Also, the minimum supply of
3.0 V must appear on one of the VPn pins in order to correctly
VP1
VP2
VP3
VP4
OFF-CHIP
DECOUPLING
CAPACITOR
ON-CHIP SUPPLY
Figure 17. V DD Arbitrator Operation
power up the ADM1060. A supply of no less than 4.5 V can be
used on VH. This is because there is no synchronous rectifier
circuit on the VH pin, resulting in a voltage drop of ~1.5 V
across the diode of the V DD arbitrator.
An external capacitor to GND is required to decouple the
on-chip supply from noise. This capacitor should be connected
to the VDDCAP pin, as shown in Figure 17. The capacitor has
another use during “brown outs” (momentary loss of power).
Under these conditions, where the input supply, VPn, dips
transiently below V DD , the synchronous rectifier switch
immediately turns off so that it does not pull V DD down. The
V DD capacitor can then act as a reservoir to keep the chip active
until the next highest supply takes over the powering of the
device. A 1 μF capacitor is recommended for this function. A
minimum capacitor value of 0.1 μF is required.
Note that in the case where there are two or more supplies
within 100 mV of each other, the supply that takes control of
V DD first will keep control. For example, if VP1 is connected to a
3.3 V supply, V DD will power up to approximately 3.1 V through
VP1. If VP2 is then connected to another 3.3 V supply, VP1 will
still power the device, unless VP2 goes 100 mV higher than
VP1.
A second capacitor is required on the VCCP pin of the
ADM1060. This capacitor is the reservoir capacitor for the
central charge pump. Again, a 1 μF capacitor is recommended
for this function. A minimum capacitor value of 0.1 μF is
required.
PROGRAMMABLE SUPPLY FAULT DETECTORS
(SFDs)
The ADM1060 has seven programmable supply fault detectors
(SFDs): one high voltage detector (+2 V to +14.4 V), two bipolar
detectors (+1 V to +6 V, ?2 V to –6 V) and four positive only
voltage detectors (+0.6 V to +6 V). Inputs are applied to these
detectors via the VH (high voltage supply input), VBn (bipolar
supply input), and VPn (positive only input) pins, respectively.
The SFDs detect a fault condition on any of these input supplies.
A fault is defined as undervoltage (where the supply drops
below a preprogrammed level), overvoltage (where the supply
rises above a preprogrammed level), or out-of-window (where
the supply deviates outside either the programmed overvoltage
or undervoltage threshold). Only one fault type can be selected
at a time.
An undervoltage (UV) fault is detected by comparing the input
supply to a programmed reference (the undervoltage threshold).
If the input voltage drops below the undervoltage threshold, the
output of the comparator goes high, asserting a fault. The
undervoltage threshold is programmed using an 8-bit DAC. On
a given range, the UV threshold can be set with a resolution of
Step Size = Threshold Range /255
An overvoltage (OV) fault is detected in exactly the same way,
using a second comparator and DAC to program the reference.
All thresholds are programmed using 8-bit registers, one regis-
ter each for the seven UV thresholds and one each for the seven
OV thresholds. The UV or OV threshold programmed by the
user is given by
Rev. B | Page 11 of 52
V T =
V R × N
255
+ V B
相关PDF资料 |
PDF描述 |
|---|---|
| LT1737IS#TRPBF | IC REG CTRLR FLYBK ISO CM 16SOIC |
| ASC06DRYN-S93 | CONN EDGECARD 12POS DIP .100 SLD |
| MIC2198YML | IC REG CTRLR BUCK PWM CM 12-MLF |
| SRP1235-R33M | INDUCTOR 330NH 36.5A SMD |
| LTC3832-1ES8#TRPBF | IC REG CTRLR BUCK PWM VM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1060ARU-REEL7 | 功能描述:IC SUPERVISOR/SEQUENCER 28TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| ADM1060ARU-U1 | 制造商:Analog Devices 功能描述:- Bulk |
| ADM1060ARUZ | 功能描述:IC SUPERVIS/SEQUENC 7-CH 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 其它有关文件:STM6717 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:2 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:1.11V，3.075V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 产品目录页面:1194 (CN2011-ZH PDF) 其它名称:497-7019-6 |
| ADM1060ARUZCS0804 | 制造商:Analog Devices 功能描述: |
| ADM1060ARUZ-REEL7 | 功能描述:IC SUPERVSR/SEQUENCR 7CH 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。