- 您现在的位置：买卖IC网 > PDF目录22118 > ADM1075-1ACPZ-RL7 (Analog Devices Inc)IC HOT SWAP CTRLR -48V 28LFCSP PDF资料下载
参数资料
| 型号： | ADM1075-1ACPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 34/52页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTRLR -48V 28LFCSP |
| 标准包装： | 1,500 |
| 类型： | 热交换控制器 |
| 应用： | -48V 远程电力系统，高可用性，电信/数据通信系统 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | -35 V ~ -80 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
X = 1/ m × ( Y × 10 ? b ) (2)
ADM1075
VAUX_OV_WARN_LIMIT and VAUX_UV_WARN_LIMIT
Commands
The VAUX_OV_WARN_LIMIT and VAUX_UV_WARN_
LIMIT commands are used to set the OV and UV thresholds
on the output voltage, as measured at the ADC_VAUX pin on
PIN_OP_WARN_LIMIT Command
The PIN_OP_WARN_LIMIT command is used to set the
overpower (OP) threshold for the power measurement register.
IOUT_OC_WARN_LIMIT Command
The IOUT_OC_WARN_LIMIT command is used to set the
overcurrent (OC) threshold for the current flowing through the
sense resistor.
IOUT_WARN2_LIMIT Command
The IOUT_WARN2_LIMIT command provides a second
current warning threshold that can be programmed. The
polarity of this warning can be set to overcurrent or
undercurrent using the DEVICE_CONFIG command.
PMBus DIRECT FORMAT CONVERSION
The ADM1075 uses the PMBus direct format internally to
represent real-world quantities such as voltage, current, and
power values. A direct format number takes the form of a
2-byte, twos complement binary integer value.
It is possible to convert between direct format value and real-world
quantities using the following equations. Equation 1 converts from
real-world quantities to PMBus direct values, and Equation 2
converts PMBus direct format values to real-world values.
Y = ( mX + b ) × 10 R (1)
?R
where:
Y is the value in PMBus direct format.
X is the real-world value.
m is the slope coefficient, a 2-byte, twos complement integer.
b is the offset, a 2-byte, twos complement integer.
R is a scaling exponent, a 1-byte, twos complement integer.
The same equations are used for voltage, current, and power
conversions, the only difference being the values of the m, b,
and R coefficients used.
coefficients shown are dependent on the value of the external
sense resistor used in a given application. This means that an
Data Sheet
The sense resistor value used in the calculations to obtain the
coefficients is expressed in milliohms. The m coefficients are
defined as 2-byte twos complement numbers in the PMBus stand-
ard; therefore, the maximum positive value that can be represented
is 32,767. If the m value is greater than that, and is to be stored
in PMBus standard form, the m coefficients should be divided
by 10, and the R coefficient increased by a value of 1. For example,
if performing a power calculation on the ADM1075-1 with a
10 mΩ sense resistor, the m coefficient is 8549, and the R
coefficient is 0.
Example 1
IOUT_OC_WARN_LIMIT requires a current limit value
expressed in direct format.
If the required current limit is 10 A, and the sense resistor is
2 mΩ, the first step is to determine the voltage coefficient. For
an ADM1075-1 , this is simply m = 806 × 2, giving 1612.
Using Equation 1, and expressing X, in units of amps,
Y = ((1612 × 10) + 20,475) × 10 ?1
Y = 3659.5 = 3660 (rounded up to integer form)
Writing a value of 3660 with the IOUT_OC_WARN_LIMIT
command sets an overcurrent warning at 10 A.
Example 2
The READ_IOUT command returns a direct format value of 3341,
representing the current flowing through a sense resistor of 1 mΩ.
To convert this value to the current flowing, use Equation 2,
X = 1/806 × (3341 × 10 1 – 20,475)
X = 16.05 A
This means that when READ_IOUT returns a value of 3341,
16.05 A is flowing in the sense resistor.
Note the following:
? The same calculations that are used to convert power
values also apply to the energy accumulator value returned
by the READ_EIN command because the energy
accumulator is a summation of multiple power values.
? The READ_PIN_EXT and READ_EIN_EXT commands
return 24-bit extended precision versions of the 16-bit
values returned by READ_PIN and READ_EIN. The direct
format values must be divided by 256 prior to being con-
additional calculation must be performed to take the sense
resistor value into account to obtain the coefficients for a
specific sense resistor value. The resistor divider scaling factor
on VIN/VAUX also needs to be taken into account when
Rev. C | Page 34 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| 2-530689-6 | CONN EDGE CARD 22POS DUAL SOLDER |
| LC4064V-75T100C | IC PLD 64MC 64I/O 7.5NS 100TQFP |
| VE-23N-EV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
| GMM06DTKI-S288 | CONN EDGECARD 12POS .156 EXTEND |
| TAP105K035DTS | CAP TANT 1UF 35V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1075-1ARUZ | 功能描述:IC CTRLR HOTSWAP -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1075-1ARUZ-RL7 | 功能描述:IC HOTSWAP CTRLR -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1075-2ACPZ | 功能描述:IC HOT SWAP CTRLR -48V 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1075-2ACPZ-RL7 | 功能描述:IC HOT SWAP CTRLR -48V 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1075-2ARUZ | 功能描述:IC CTRLR HOTSWAP -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。