- 您现在的位置：买卖IC网 > PDF目录373996 > ADM1172 (Analog Devices, Inc.) 2.7 V to 16.5 V Hot Swap Controller with Power-Fail Comparator PDF资料下载
参数资料
| 型号： | ADM1172 |
| 厂商： | Analog Devices, Inc. |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | 2.7 V to 16.5 V Hot Swap Controller with Power-Fail Comparator |
| 中文描述： | 2.7 V至16.5 V热风热插拔控制器与电源失效比较 |
| 文件页数： | 13/16页 |
| 文件大小： | 181K |
| 代理商： | ADM1172 |
ADM1172
gate voltage of the external FET. This minimizes the bus supply
voltage drop caused by the fault and protects neighboring cards.
Rev. 0 | Page 13 of 16
When the initial cycle ends, a start-up cycle activates and the
GATE pin is pulled high; the TIMER pin continues to pull down.
1
2
NORMAL
CYCLE
INITIAL
CYCLE
START-UP
CYCLE
RESET
MODE
3
4
V
IN
V
ON
V
TIMER
V
GATE
V
OUT
0
As the voltage across the sense resistor approaches the current
limit, a timer activates. This timer resets again if the sense
voltage returns below this level. If the sense voltage is any
voltage below 44 mV, the timer is guaranteed to be off. Should
the current continue to increase, the ADM1172 tries to regulate
the gate of the FET to achieve a limit of 50 mV across the sense
resistor. However, if the device is unable to regulate the fault
current and the sense voltage further increases, a larger pull-
down, in the order of milliamperes, is enabled to compensate
for fast current surges. If the sense voltage is any voltage greater
than 56 mV, this pull-down is guaranteed to be on. When the
timer expires, the GATE pin shuts down.
TIMER FUNCTION
The TIMER pin is responsible for several key functions on the
ADM1172. A capacitor controls the initial power on reset time
and the amount of time an overcurrent condition lasts before
the FET shuts down. On the ADM1172-1, the timer pin also
controls the time between auto retry pulses. There are pull-up
and pull-down currents internally available to control the timer
functions. The voltage on the TIMER pin is compared with two
threshold voltages: COMP1 (0.2 V) and COMP2 (1.3 V). The
four timing currents are listed in
Table 5.
Timing Current
Pull-up
Pull-up
Pull-down
Pull-down
Figure 38. Power-Up Timing
Table 5.
Level (μA)
5
60
2
100
2μA
5μA
60μA
100μA
V
IN
V
ON
V
TIMER
V
GATE
V
OUT
I
RSENSE
NORMAL
CYCLE
INITIAL
CYCLE
START-UP
CYCLE
RESET
MODE
Figure 39. Power-Up into Capacitor
0
POWER-UP TIMING CYCLE
The ADM1172 is in reset when the ON (ON-
low. The GATE pin is pulled low and the TIMER pin is pulled
low with a 100 μA pull-down. At Time Point 2 in Figure 38, the
ON (ON-CLR) pin is pulled high. For the device to startup
correctly, the supply voltage must be above UVLO, the ON
(ON-
CLR) pin must be above 1.3 V, and the TIMER pin voltage
must be less than 0.2 V The initial timing cycle begins when these
three conditions are met, and the TIMER pin is pulled high with
5 μA. At Time Point 3, the TIMER reaches the COMP2 threshold.
CLR
) pin is held
CIRCUIT BREAKER TIMING CYCLE
When the voltage across the sense resistor exceeds the circuit
breaker trip voltage, the 60 μA timer pull-up current is activated.
If the sense voltage falls below this level before the TIMER pin
reaches 1.3 V, the 60 μA pull-up is disabled and the 2 μA pull-
down is enabled. This is likely to happen if the overcurrent fault
is only transient, such as an inrush current. This is shown in
Figure 39. However, if the overcurrent condition is continuous
and the sense voltage remains above the circuit breaker trip
voltage, the 60 μA pull-up remains active. This allows the TIMER
pin to reach the high trip point of 1.3 V and initiate the GATE
shutdown. On the ADM1172-2, the TIMER pin continues pulling
up but switches to the 5 μA pull-up when it reaches the 1.3 V
This is the end of the first section of the initial cycle. The 100 μA
current source then pulls down the TIMER pin until it reaches
0.2 V at Time Point 4. The initial cycle delay (Time Point 2 to
Time Point 4) relates to C
TIMER
by equation
t
INITIAL
= 1.3 ×
C
TIMER
/5 μA
(4)
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1172-1AUJZ-RL7 | 2.7 V to 16.5 V Hot Swap Controller with Power-Fail Comparator |
| ADM1172-2AUJZ-RL7 | 2.7 V to 16.5 V Hot Swap Controller with Power-Fail Comparator |
| ADM1185ARMZ-1 | Quad Voltage Monitor and Sequencer |
| ADM1185 | Quad Voltage Monitor and Sequencer |
| ADM1185_07 | Quad Voltage Monitor and Sequencer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1172-1AUJZ-RL7 | 功能描述:IC CTRLR HOTSWAP 16.5V TSOT-23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1172-2AUJZ-RL7 | 功能描述:IC CTRLR HOTSWAP 16.5V TSOT-23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1175 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with Convert Pin |
| ADM1175-1ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1175-2ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。