- 您现在的位置：买卖IC网 > PDF目录10211 > ADM1181AARWZ-REEL (Analog Devices Inc)IC TXRX RS-232 5V 15KV 16SOIC PDF资料下载
参数资料
| 型号： | ADM1181AARWZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS-232 5V 15KV 16SOIC |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
ADM202E/ADM1181A
Rev. C | Page 10 of 16
ESD TESTING (IEC1000-4-2)
IEC1000-4-2 (previously 801-2) specifies compliance testing
using two coupling methods, contact discharge and air-gap
discharge. Contact discharge calls for a direct connection to the
unit being tested. Air-gap discharge uses a higher test voltage,
but does not make direct contact with the unit being tested.
With air-gap discharge, the discharge gun is moved toward the
unit being tested, developing an arc across the air gap. This
method is influenced by humidity, temperature, barometric
pressure, distance, and rate of closure of the discharge gun.
Although less realistic, the contact-discharge method is more
repeatable and is gaining preference to the air-gap method.
Although very little energy is contained within an ESD pulse,
the extremely fast rise time coupled with high voltages can
cause failures in unprotected semiconductors. Catastrophic
destruction can occur immediately as a result of arcing or
heating. Even if catastrophic failure does not occur immediately,
the device might suffer from parametric degradation, which can
result in degraded performance. The cumulative effects of
continuous exposure can eventually lead to complete failure.
I/O lines are particularly vulnerable to ESD damage. Simply
touching or plugging in an I/O cable can result in a static
discharge, which can damage or completely destroy the
interface product connected to the I/O port. Traditional ESD
test methods, such as the MIL-STD-883B method 3015.7, do
not fully test a product’s susceptibility to this type of discharge.
This test was intended to test a product’s susceptibility to ESD
damage during handling. Each pin is tested with respect to all
other pins. There are some important differences between the
traditional test and the IEC test:
The IEC test is much more stringent in terms of discharge
energy. The injected peak current is over four times greater.
The current rise time is significantly faster in the IEC test.
The IEC test is carried out while power is applied to
the device.
It is possible that the ESD discharge could induce latch-up in the
device being tested. Therefore, this test is more representative of a
real-world I/O discharge where the equipment is operating
normally with power applied. For peace of mind, however, both
tests should be performed to ensure maximum protection
during both handling and field service.
R1
R2
C1
DEVICE
UNDER TEST
HIGH
VOLTAGE
GENERATOR
ESD TEST METHOD
R2
C1
H. BODY MIL-STD883B
1.5k
100pF
IEC1000-4-2
330
150pF
00066-018
Figure 18. ESD Test Standards
100
I PEA
K
(%)
90
36.8
10
tDL
tRL
TIME t
00066-019
Figure 19. Human Body Model ESD Current Waveform
100
I PEA
K
(%)
90
10
TIME t
30ns
60ns
0.1 TO 1ns
00066-020
Figure 20. IEC1000-4-2 ESD Current Waveform
The ADM202E/ADM1181E products are tested using both of
the previously mentioned test methods. Pins are tested with
respect to all other pins as per the MIL-STD-883B specification.
In addition, I/O pins are tested as per the IEC test specification.
The products were tested under the following conditions:
Power-On
Power-Off
There are four levels of compliance defined by IEC1000-4-2. The
ADM202E/ADM1181A products meet the most stringent level
of compliance both for contact and for air-gap discharge. This
means that the products are able to withstand contact discharges
in excess of 8 kV and air-gap discharges in excess of 15 kV.
相关PDF资料 |
PDF描述 |
|---|---|
| CXC3106A1811P | CONN PLUG 5POS STRGHT PIN |
| D38999/24WC8PB | CONN RCPT 8POS JAM NUT W/PINS |
| AD9223ARZ-REEL | IC ADC 12BIT 3.0MSPS 28SOIC |
| EN3P11F26X | CONN RCPT 11POS FEMALE PANEL #26 |
| MS27473T16F35SA | CONN PLUG 55POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1184 | 制造商:AD 制造商全称:Analog Devices 功能描述:0.8% Accurate Quad Voltage Monitor |
| ADM1184ARMZ | 功能描述:IC VOLT MONITOR/SEQ 4CH 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| ADM1184ARMZ | 制造商:Analog Devices 功能描述:; Leaded Process Compatible:Yes; Peak Re |
| ADM1184ARMZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:0.8% Accurate Quad Voltage Monitor |
| ADM1184ARMZ-REEL7 | 功能描述:IC VOLT MONITOR/SEQ 4CH 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。