- 您现在的位置：买卖IC网 > PDF目录22115 > ADM1275-1ACPZ-R7 (Analog Devices Inc)IC HOT SWAP CTRL PMBUS 20LFCSP PDF资料下载
参数资料
| 型号： | ADM1275-1ACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/48页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTRL PMBUS 20LFCSP |
| 标准包装： | 1,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.95 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-ADM1275EBZ-ND - BOARD EVALUATION FOR ADM1275 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
V TIMERH × C TIMER ( V TIMERH ? V TIMERL ) × C TIMER
ADM1275
TIMER
The TIMER pin handles several timing functions with an
external capacitor, C TIMER . The two comparator thresholds are
V TIMERL (0.2 V) and V TIMERH (1 V). There are four timing current
sources: a 3 μA pull-up, a 60 μA pull-up, a 2 μA pull-down, and
a 100 μA pull-down.
These current and voltage levels, together with the value of
C TIMER chosen by the user, determine the initial timing cycle
time, the fault current limit time, and the hot-swap retry duty
cycle. The TIMER capacitor value is determined using the
following equation:
C TIMER = ( t ON × 60 μA)/ V TIMERH
where t ON is the time that the FET is allowed to spend in regu-
lation at the set current limit. The choice of FET is based on
matching this time with the SOA requirements of the FET.
Foldback can be used to simplify the selection.
When VCC is connected to the backplane supply, the internal
supply of the ADM1275 must be charged up. In a very short
time, the internal supply is fully charged up and, because the
undervoltage lockout (UVLO) voltage is exceeded at VCC, the
device comes out of reset. During this first short reset period,
the GATE and TIMER pins are both held low.
The ADM1275 then goes through an initial timing cycle. The
TIMER pin is pulled high with 3 μA. When the TIMER reaches
the V TIMERH threshold (1.0 V), the first portion of the initial timing
cycle is complete. The 100 μA current source then pulls down the
TIMER pin until it reaches V TIMERL (0.2 V). The initial timing
cycle duration is related to C TIMER by the following equation:
t INITIAL = +
3 μ A 100 μ A
For example, a 100 nF capacitor results in a delay of approxi-
mately 34 ms. If the UV and OV inputs indicate that the supply
is within the defined window of operation when the initial
timing cycle terminates, the device is ready to start a hot-swap
operation.
When the voltage across the sense resistor reaches the circuit
breaker trip voltage, V CB , the 60 μA timer pull-up current is
activated, and the gate begins to regulate the current at the
current limit. This initiates a ramp-up on the TIMER pin. If the
sense voltage falls below this circuit breaker trip voltage before
the TIMER pin reaches V TIMERH , the 60 μA pull-up is disabled
and the 2 μA pull-down is enabled.
The circuit breaker trip voltage is not the same as the hot-swap
sense voltage current limit. There is a small circuit breaker offset,
V CBOS , which means that the timer actually starts a short time
before the current reaches the defined current limit.
Data Sheet
However, if the overcurrent condition is continuous and the
sense voltage remains above the circuit breaker trip voltage, the
60 μA pull-up remains active and the FET remains in regulation.
This allows the TIMER pin to reach V TIMERH and initiate the
GATE shutdown. On the ADM1275 -1 and ADM1275 -3, the
LATCH pin is pulled low immediately.
In latch-off mode, the TIMER pin is switched to the 2 μA
pull-down when it reaches the V TIMERH threshold. The LATCH
pin ( ADM1275 -1 and ADM1275 -3) remains low. While the
TIMER pin is being pulled down, the hot-swap controller is
kept off and cannot be turned back on.
When the voltage on the TIMER pin goes below the V TIMERL
threshold, the hot-swap controller can be reenabled by toggling
the UV pin or by using the PMBus OPERATION command to
toggle the ON bit from on to off and then on again.
HOT-SWAP RETRY DUTY CYCLE
The ADM1275 -1 and ADM1275 -3 turn off the FET after an
overcurrent fault and then use the capacitor on the TIMER pin
to provide a delay before automatically retrying the hot-swap
operation. To configure the ADM1275 -1 and ADM1275 -3 for
autoretry mode, the LATCH pin is tied to the UV pin or to the
ENABLE pin ( ADM1275 -3 only). Note that a pull-up is
required on the LATCH pin.
When an overcurrent fault occurs, the TIMER capacitor is
charged with a 60 μA pull-up current. When the TIMER pin
reaches V TIMERH , the GATE pin is pulled down. When the
LATCH pin is tied to the UV pin or the ENABLE pin for
autoretry mode, the TIMER pin is pulled down with a 2 μA
current sink. When the TIMER pin reaches V TIMERL (0.2 V),
it automatically restarts the hot-swap operation.
The duty cycle of this automatic retry cycle is set by the ratio of
2 μA/60 μA, which approximates to being on about 4% of the
time. The value of the timer capacitor determines the on time of
this cycle, which is calculated as follows:
t ON = V TIMERH × ( C TIMER /60 μA)
t OFF = ( V TIMERH ? V TIMERL ) × ( C TIMER /2 μA)
A 100 nF TIMER capacitor gives an on time of 1.67 ms and an
off time of 40 ms. The device retries indefinitely in this manner
and can be disabled manually by holding the UV or ENABLE
pin low or by disconnecting the LATCH pin. To prevent thermal
stress, an RC network can be used to extend the retry time to
any desired level.
FET GATE DRIVE CLAMPS
The charge pump used on the GATE pin is capable of driving
the pin to V CC + (2 × V CC ), but it is clamped to less than 14 V
above the SENSE pins and less than 31 V. These clamps ensure
that the maximum V GS rating of the FET is not exceeded.
Rev. D | Page 24 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| LC4064C-75TN100C | IC CPLD 64MACROCELLS 100TQFP |
| VE-BWK-CY-F3 | CONVERTER MOD DC/DC 40V 50W |
| VE-23M-CY-B1 | CONVERTER MOD DC/DC 10V 50W |
| LC4064B-75TN100C | IC CPLD 64MACROCELLS 100TQFP |
| TAP105K020CRS | CAP TANT 1UF 20V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1275-1ARQZ | 功能描述:IC HOT SWAP CTRL PMBUS 20QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1275-1ARQZ-R7 | 功能描述:IC HOT SWAP CTRL PMBUS 20QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1275-2ARQZ | 功能描述:IC HOT SWAP CTRL PMBUS 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1275-2ARQZ-R7 | 功能描述:IC HOT SWAP CTRL PMBUS 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1275-3ACPZ | 功能描述:IC HOT SWAP CTRL PMBUS 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。