- 您现在的位置：买卖IC网 > PDF目录22107 > ADM1275-1ACPZ (Analog Devices Inc)IC HOT SWAP CTRL PMBUS 20LFCSP PDF资料下载
参数资料
| 型号： | ADM1275-1ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/48页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTRL PMBUS 20LFCSP |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.95 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
| 配用： | EVAL-ADM1275EBZ-ND - BOARD EVALUATION FOR ADM1275 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Data Sheet
THEORY OF OPERATION
ADM1275
When circuit boards are inserted into a live backplane, discharged
2.95V TO 20V
R SENSE
Q 1
supply bypass capacitors draw large transient currents from the
backplane power bus as they charge. These transient currents can
cause permanent damage to connector pins, as well as dips on
22 ?
SENSE+
SENSE–
the backplane supply that can reset other boards in the system.
The ADM1275 is designed to control the powering on and off
of a system in a controlled manner, allowing a board to be removed
from, or inserted into, a live backplane by protecting it from excess
currents. The ADM1275 can reside on the back-plane or on the
VCC
330nF
ADM1275
GATE
removable board.
POWERING THE ADM1275
A supply voltage from 2.95 V to 20 V is required to power the
ADM1275 via the VCC pin. The VCC pin provides the majority
of the bias current for the device; the remainder of the current
needed to control the gate drive and best regulate the V GS
voltage is supplied by the SENSE+ pin.
To ensure correct operation of the ADM1275 , the voltage on
the VCC pin must be greater than or equal to the voltage on
the SENSE+ pin. No sequencing of the VCC and SENSE+ rails
GND
Figure 47. Transient Glitch Protection Using an RC Network
CURRENT SENSE INPUTS
The load current is monitored by measuring the voltage drop
across an external sense resistor, R SENSE (see Figure 48). An
internal current sense amplifier provides a gain of 50 to the
voltage drop detected across R SENSE . The result is compared to
an internal reference and used by the hot-swap control logic to
detect when an overcurrent condition occurs.
is necessary. The SENSE+ pin can be as low as 2 V for normal
operation provided that a voltage of at least 2.95 V is connected
to the VCC pin. In most applications, both the VCC and SENSE+
pins are connected to the same voltage rail, but they are connected
via separate traces to prevent accuracy loss in the sense voltage
SENSE+
R SENSE
SENSE–
Q 1
+
×50
–
2.95V TO 20V
R SENSE
Q 1
VCC
+
OVER-
CURRENT
GATE
REFERENCE
–
SENSE+
SENSE–
ADM1275
GND
VCC
ADM1275
GATE
Figure 48. Hot-Swap Current Sense Amplifier
The SENSE inputs may be connected to multiple parallel sense
resistors, which can affect the voltage drop detected by the
GND
Figure 46. Powering the ADM1275
To protect the ADM1275 from unnecessary resets due to transient
supply glitches, an external resistor and capacitor can be added,
as shown in Figure 47. The values of these components should be
chosen to provide a time constant that can filter any expected
glitches. The resistor should, however, be small enough to keep
voltage drops due to quiescent current to a minimum. A supply
creates an offset, resulting in reduced accuracy.
To achieve better accuracy, averaging resistors sum the current
from the nodes of each sense resistor, as shown in Figure 49. The
typical value for the averaging resistors is 10 Ω. The value of the
averaging resistors is chosen to be much greater than the trace
resistance between the sense resistors terminals and the inputs
to the ADM1275 . This greatly reduces the effects of differences
in the trace resistances.
decoupling capacitor should not be placed on the rail before the
FET unless a resistor is used to limit the inrush current.
Rev. D | Page 21 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23B-EV-F2 | CONVERTER MOD DC/DC 95V 150W |
| RSM44DRUS | CONN EDGECARD 88POS DIP .156 SLD |
| 1-530844-7 | CONN CARDEDGE II 28POS PCB GOLD |
| VI-23B-EV-F1 | CONVERTER MOD DC/DC 95V 150W |
| TAP104M035CRW | CAP TANT 0.1UF 35V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1275-1ACPZ-R7 | 功能描述:IC HOT SWAP CTRL PMBUS 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1275-1ARQZ | 功能描述:IC HOT SWAP CTRL PMBUS 20QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1275-1ARQZ-R7 | 功能描述:IC HOT SWAP CTRL PMBUS 20QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1275-2ARQZ | 功能描述:IC HOT SWAP CTRL PMBUS 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1275-2ARQZ-R7 | 功能描述:IC HOT SWAP CTRL PMBUS 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。