- 您现在的位置：买卖IC网 > PDF目录10815 > ADM202EARUZ (Analog Devices Inc)IC TX/RX RS-232 5V 15KV 16TSSOP PDF资料下载
参数资料
| 型号： | ADM202EARUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC TX/RX RS-232 5V 15KV 16TSSOP |
| 标准包装： | 96 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 789 (CN2011-ZH PDF) |
ADM202E/ADM1181A
Rev. C | Page 10 of 16
ESD TESTING (IEC1000-4-2)
IEC1000-4-2 (previously 801-2) specifies compliance testing
using two coupling methods, contact discharge and air-gap
discharge. Contact discharge calls for a direct connection to the
unit being tested. Air-gap discharge uses a higher test voltage,
but does not make direct contact with the unit being tested.
With air-gap discharge, the discharge gun is moved toward the
unit being tested, developing an arc across the air gap. This
method is influenced by humidity, temperature, barometric
pressure, distance, and rate of closure of the discharge gun.
Although less realistic, the contact-discharge method is more
repeatable and is gaining preference to the air-gap method.
Although very little energy is contained within an ESD pulse,
the extremely fast rise time coupled with high voltages can
cause failures in unprotected semiconductors. Catastrophic
destruction can occur immediately as a result of arcing or
heating. Even if catastrophic failure does not occur immediately,
the device might suffer from parametric degradation, which can
result in degraded performance. The cumulative effects of
continuous exposure can eventually lead to complete failure.
I/O lines are particularly vulnerable to ESD damage. Simply
touching or plugging in an I/O cable can result in a static
discharge, which can damage or completely destroy the
interface product connected to the I/O port. Traditional ESD
test methods, such as the MIL-STD-883B method 3015.7, do
not fully test a product’s susceptibility to this type of discharge.
This test was intended to test a product’s susceptibility to ESD
damage during handling. Each pin is tested with respect to all
other pins. There are some important differences between the
traditional test and the IEC test:
The IEC test is much more stringent in terms of discharge
energy. The injected peak current is over four times greater.
The current rise time is significantly faster in the IEC test.
The IEC test is carried out while power is applied to
the device.
It is possible that the ESD discharge could induce latch-up in the
device being tested. Therefore, this test is more representative of a
real-world I/O discharge where the equipment is operating
normally with power applied. For peace of mind, however, both
tests should be performed to ensure maximum protection
during both handling and field service.
R1
R2
C1
DEVICE
UNDER TEST
HIGH
VOLTAGE
GENERATOR
ESD TEST METHOD
R2
C1
H. BODY MIL-STD883B
1.5k
100pF
IEC1000-4-2
330
150pF
00066-018
Figure 18. ESD Test Standards
100
I PEA
K
(%)
90
36.8
10
tDL
tRL
TIME t
00066-019
Figure 19. Human Body Model ESD Current Waveform
100
I PEA
K
(%)
90
10
TIME t
30ns
60ns
0.1 TO 1ns
00066-020
Figure 20. IEC1000-4-2 ESD Current Waveform
The ADM202E/ADM1181E products are tested using both of
the previously mentioned test methods. Pins are tested with
respect to all other pins as per the MIL-STD-883B specification.
In addition, I/O pins are tested as per the IEC test specification.
The products were tested under the following conditions:
Power-On
Power-Off
There are four levels of compliance defined by IEC1000-4-2. The
ADM202E/ADM1181A products meet the most stringent level
of compliance both for contact and for air-gap discharge. This
means that the products are able to withstand contact discharges
in excess of 8 kV and air-gap discharges in excess of 15 kV.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J6P-MY-S | CONVERTER MOD DC/DC 13.8V 50W |
| ADM202EARNZ | IC TXRX RS-232 5V 15KV 16SOIC |
| VI-J6N-MY-S | CONVERTER MOD DC/DC 18.5V 50W |
| VI-B41-IV-S | CONVERTER MOD DC/DC 12V 150W |
| ADM202EARWZ | IC TX/RX RS-232 5V 15KV 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM202EARUZ | 制造商:Analog Devices 功能描述:RS-232 IC |
| ADM202EARUZ-REEL | 功能描述:IC TXRX RS-232 5V 15KV 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:121 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:3 V ~ 3.6 V 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:管件 |
| ADM202EARUZ-REEL7 | 功能描述:IC TXRX RS232 5V 15KV 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:121 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:3 V ~ 3.6 V 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:管件 |
| ADM202EARW | 功能描述:IC TX/RX RS-232 5V 15KV 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:121 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:3 V ~ 3.6 V 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:管件 |
| ADM202EARW-REEL | 功能描述:IC TX/RX RS-232 5V 15KV 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:121 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:3 V ~ 3.6 V 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。