- 您现在的位置：买卖IC网 > PDF目录1775 > ADM6306D344ARJZ-R7 (Analog Devices Inc)IC SUPERVISOR DUAL SOT23-5 PDF资料下载
参数资料
| 型号： | ADM6306D344ARJZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR DUAL SOT23-5 |
| 标准包装： | 3,000 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.38V，可调 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
ADM6305/ADM6306
THEORY OF OPERATION
The ADM6305/ADM6306 are compact, low power supervisory
circuits capable of monitoring two voltage rails. If a monitored
voltage drops below its associated threshold, the active low reset
output asserts low.
The ADM6305 monitors two supplies via two adjustable
resistor-programmable undervoltage reset inputs. Both RST
IN1 and RST IN2 have a reset threshold of either 0.4 V or
1.23 V depending on the particular model; that is, the RST
IN1 and RST IN2 threshold of the ADM6305DxARJZ model
is 1.23 V, while in the case of ADM6305DxARJZ1 model, it is
0.4 V. The V CC input of the ADM6305 is not a monitored input.
The ADM6306 has one adjustable undervoltage reset input,
RST IN, which features a choice of reset threshold, 0.4 V or
1.23 V (see the Ordering Guide for more information). The
ADM6306 incorporates a variety of internally pretrimmed V CC
undervoltage threshold options for monitoring supply voltages
in increments between 2.5 V to 5 V. The ADM6306 also
includes a manual reset input.
INPUT CONFIGURATION
The threshold voltage at an adjustable input is either 0.4 V or
1.23 V. To monitor a voltage greater than the typical adjustable
threshold, V RSTH , connect a resistor divider network to the
circuit as depicted in Figure 14, where
Data Sheet
on this input. The ADM6305/ADM6306 are powered via V CC .
threshold overdrive, for which reset pulses are not generated.
V CC transient may typically have without causing RESET to be
asserted. As the amplitude of the transient increases, the
maximum allowable pulse width decreases. The addition of a
bypass capacitor on V CC provides additional transient immunity.
RESET OUTPUT CONFIGURATION
The ADM6305/ADM6306 are available in a choice of four
reset timeouts. Once the monitored supplies rise above their
associated threshold level, the RESET signal remains low for
the reset timeout period before deasserting. Subsequently, if
a monitored supply falls below its associated threshold, the
RESET output reasserts. The open-drain RESET output of the
ADM6305/ADM6306 remains valid as long as V CC exceeds 0.9 V.
The ADM6305 remains in UVLO when V CC is below 1.5 V. The
RESET output is controlled by RTS INx if V CC exceeds 2.5 V.
The open-drain RESET output allows the ADM6305 and
ADM6306 to interface easily with microprocessors and
devices with bidirectional reset pins. Connecting the supervi-
sory devices RESET output directly to the microcontrollers
RESET pin with a single pull-up resistor allows either device
V TH ? V RSTH ? ?
R1 ? R2 ?
?
?
R2
V IN
?
to issue a system reset (see Figure 15).
V CC
R1
R2
ADM6305/
ADM6306
RESET
R PULL-UP
MICROPROCESSOR
RESET
V RSTH
Figure 15. Interfacing to Microprocessors with Bidirectional RESET Output
Figure 14. Setting the Adjustable Monitor
The high input impedance (leakage of ±25 nA) of the adjustable
inputs minimizes the offset error caused by the leakage current
and external resistor divider. This allows the user to apply a divider
with large resistance to minimize the loss. The offset voltage
caused by the leakage current is calculated by R1 × ±25 nA.
The RST INx inputs are designed to ignore fast voltage
transients (see Figure 11 and Figure 12). Increase the noise
immunity by connecting a 0.1 μF bypass capacitor between
RST INx and ground. Note that adding capacitance to RST
INx slows the overall response time of the device.
There is no hysteresis associated with the 0.4 V adjustable
inputs; instead, a time-based glitch filter to prevent false
triggering is used. The glitch filter avoids the need to use a
MANUAL RESET
The ADM6306 features a manual reset input (MR) which, when
driven low, asserts the reset output. When MR transitions from
low to high, reset remains asserted for the duration of the reset
active timeout period before deasserting. The MR input has a
63.5 kΩ internal pull-up resistor so that the input is always
high when unconnected. An external push-button switch can
be connected between MR and ground so that the user can
generate a reset. Debounce circuitry is integrated on-chip for
this purpose. Noise immunity is provided on the MR input,
and fast, negative-going transients of up to 0.1 μs (typical) are
ignored. If required, a 0.1 μF capacitor between MR and ground
provides additional noise immunity.
portion of the operating supply range to provide hysteresis
Rev. A | Page 8 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| ADM6315-26D2ARTRL7 | IC SUPERVISOR OD 2.63V SOT143 |
| ADM6318CY45ARJZ-R7 | IC SUPERVISOR WATCHDOG SOT23-5 |
| ADM6339LARJZ-RL7 | IC MCU SUP ADJ/33/25/ADJ SOT23-6 |
| ADM6346-44ARTZ-R7 | IC MPU RESET CIRC 4.38V SOT23-3 |
| ADM6384YKS29D1-RL7 | IC SUPERVISOR MPU RESET SC70-4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM6306D346ARJZ-R7 | 功能描述:IC SUPERVISOR DUAL SOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM6308 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Eight-port 10/100M Ethernet Switch Controller |
| ADM6315 | 制造商:AD 制造商全称:Analog Devices 功能描述:Open-Drain Microprocessor Supervisory Circuit in 4-Lead SOT-143 |
| ADM6315_VE | 制造商:AD 制造商全称:Analog Devices 功能描述:Open-Drain Microprocessor Supervisory Circuit in 4-Lead SOT-143 |
| ADM6315-25D1ART-RL | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage Detector |
发布紧急采购，3分钟左右您将得到回复。