- 您现在的位置：买卖IC网 > PDF目录15388 > ADM690AARN-REEL (Analog Devices Inc)IC SUPERVISOR MPU 4.65V WD 8SOIC PDF资料下载
参数资料
| 型号： | ADM690AARN-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU 4.65V WD 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
ADM690A/ADM692A/ADM802L/M/ADM805L/M
If the watchdog timer is not needed, the WDI input should be
left floating.
The Power Fail Input, PFI, monitors the input power supply via
a resistive divider network. The voltage on the PFI input is
compared with a precision 1.25 V internal reference. If the input
voltage drops below 1.25 V, a power fail output ( PFO ) signal is
generated. This warns of an impending power failure and may
be used to interrupt the processor so that the system may be
shut down in an orderly fashion. The resistors in the sensing
network are ratioed to give the desired power fail threshold
voltage V T .
V T = (1.25 R 1/ R 2) + 1.25 V
R 1/ R 2 = ( V T /1.25) – 1
Alternate Watchdog Input Drive Circuits
The watchdog feature can be enabled and disabled under
program control by driving WDI with a 3-state buffer. When
three-stated, the WDI input will float thereby disabling the
watchdog timer.
Operation Without a Backup Supply
If a backup power source is not used, V BATT should be con-
nected to GND and V OUT should be connected to V CC .
Replacing the Backup Battery
The backup battery may be replaced without any danger of
spurious resetting when V CC is present. Since V CC is above the
reset threshold, a reset will not occur even if V BATT is floating
while a replacement battery is being inserted. This differs from
older generation products where leakage currents flowing out
V BATT could cause spurious resetting during battery replacement.
Ps With Bidirectional RESET
In order to prevent contention for microprocessors with a
bidirectional reset line, a current limiting resistor should be
inserted between the ADM69xA/ADM80xx RESET output pin
and the μ P reset pin. This will limit the current to a safe level if
there are conflicting output reset levels. A suitable resistor value
is 4.7 k ? . If the reset output is required for other uses, then it
should be buffered as shown in Figure 13.
High Capacity Backup Capacitors
High capacity (0.1 μ F or greater) capacitors may be used as a
backup power source. A typical application is shown in Fig-
ure 12.
+5V
+5V
V CC
ADM690A
ADM692A
ADM802L
ADM802M
BUFFERED
RESET
μP
V CC
V BATT
V OUT
RESET
RESET *
TO STATIC RAM
TO μP
RESET
GND
RESET
GND
0.1F
+
GND
Figure 13. Bidirectional Reset
* FOR ADM805L/ADM805M ONLY
Figure 12. High Capacity Capacitor
REV. 0
–7 –
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JWW-EY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| ESM24DSEN | CONN EDGECARD 48POS .156 EYELET |
| H2AXT-10108-Y4-ND | JUMPER-H1502TR/A2015Y/X 8" |
| RCM22DTKN-S288 | CONN EDGECARD 44POS .156 EXTEND |
| B43086A4685M | 6.8UF 350V 10X16 SINGLE END |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM690AARNZ | 功能描述:IC SUPERVISOR MPU 4.65 WD 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| ADM690AARNZ | 制造商:Analog Devices 功能描述:Controller IC |
| ADM690AARNZ-REEL | 功能描述:IC SUPERVISOR MPU 4.65V WD 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM690ADM695 | 制造商:AD 制造商全称:Analog Devices 功能描述:Microprocessor Supervisory Circuits |
| ADM690-ADM695 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microprocessor Supervisory Circuits |
发布紧急采购，3分钟左右您将得到回复。