参数资料
| 型号： | ADM698AN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU 4.65V 8DIP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
ADM698/ADM699
CIRCUIT INFORMATION
Power Fail RESET
A precision voltage detector monitors V CC and generates a
RESET output to hold the microprocessor’s Reset line low when
V CC falls below the reset threshold (4.65 V) (see Figure 4). The
reset voltage threshold is set to accommodate a 5% variation on
V CC . The voltage detector has 40 mV hysteresis to ensure that
glitches on V CC do not activate the RESET output.
On power up, an internal monostable holds RESET low for
140 ms after V CC rises above the reset threshold. This allows the
power supply to stabilize on power up and also prevents re-
peated toggling of RESET even if the 5 V power drops out and
recovers with each power line cycle. In order to prevent
mistriggering due to transient voltage spikes, it is recommended
that a 0.1 μ F capacitor be connected at the V CC pin.
The RESET output is guaranteed to remain low with V CC as
low as 1 V. This holds the microprocessor in a stable shutdown
condition as the power supply comes up.
On the 16-lead SOIC package, an active high RESET output is
also provided. This is the complement of RESET and is in-
tended for microprocessors requiring an active high signal.
Watchdog Timer (ADM699 Only)
The watchdog timer input (WDI) monitors an I/O line from the
μ P system. The μ P must toggle this input once every 1.6 sec-
onds to verify correct software execution. Failure to toggle the
line indicates that the μ P system is not correctly executing its
program and may be tied up in an endless loop. If this happens,
a reset pulse is generated to initialize the processor.
The WDI input is a three level input and will recognize a low
to- high or a high-to-low transition on its input. The watchdog
timer is reset by each WDI transition and then begins its
timeout period. If the WDI pin remains either high or low, reset
pulses will be issued every 1.6 seconds typically. If the watch-
dog timer is not needed, the WDI input should be left floating.
The Watchdog Output ( WDO ) (SOIC package Only) provides
watchdog status information. It is driven low if WDI is not
toggled within the watchdog timeout period. It goes high at the
next WDI transition. It is also set high when V CC falls below the
reset threshold.
WDI
V CC
V 2
V 1
V 2
V 1
WDO
t 2
t 2
RESET
t 1
t 1
RESET
V 1 = RESET VOLTAGE THRESHOLD
t 1
t 1
t 1
V 2 = RESET VOLTAGE THRESHOLD +
THRESHOLD HYSTERESIS
t 1 = RESET TIME
Figure 4. Watchdog Timeout Period vs. Temperature
t 1 = RESET TIME
t 2 = WATCHDOG TIME OUT PERIOD
Figure 5. Watchdog Timeout Period and Reset Active Time
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Pin Plastic DIP
(N-8)
8-Pin Cerdip
(Q-8)
5
8
16-Lead SOIC
(R-16)
PIN 1
1
4
0.310 (7.87)
0.220 (5.59)
0.299
(7.60)
16
9
0.419
(10.65)
0.420 (10.67)
MAX
0.060 (1.52)
0.200
0.015 (0.38)
1
8
(5.08)
MAX
0.150
SEATING
PLANE
(3.81)
MIN
0.012
(0.3)
0.413 (10.50)
0.104
0.022 (0.558)
0.014 (0.356)
0.100 (2.54)
BSC
0.070 (1.78)
(2.65)
0.320 (8.13)
0.290 (7.37)
0.30 (0.76)
0.030
(0.75)
0.013
0.05 (1.27)
REF
0.019 (0.49)
0.015 (0.381)
0.008 (0.204)
–4 –
(0.32)
0.042
(1.07)
REV. 0
相关PDF资料 |
PDF描述 |
|---|---|
| ADM706RAR | IC SUPERVISOR MPU 2.63V WD 8SOIC |
| ADM707AR | IC SUPERVISOR MPU 4.65 WD 8SOIC |
| ADM709TAR | IC SUPERVISOR MPU 3.08V RS 8SOIC |
| ADM800MARN | IC SUPERVISOR MPU 4.40V 16SOIC |
| ADM809-5SARTZ-REEL7 | IC SUPERVISOR MPU 2.93V SOT23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM698ANZ | 功能描述:IC SUPERVISOR MPU 4.65V 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6717 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:2 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:1.11V，3.075V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 产品目录页面:1194 (CN2011-ZH PDF) 其它名称:497-7019-6 |
| ADM698AQ | 制造商:AD 制造商全称:Analog Devices 功能描述:Microprocessor Supervisory Circuits |
| ADM698AR | 功能描述:IC SUPERVISOR MPU 4.65V 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM698AR-REEL | 功能描述:IC SUPERVISOR MPU 4.65V 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM698ARZ | 功能描述:IC SUPERVISOR MPU 4.65V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
发布紧急采购，3分钟左右您将得到回复。