- 您现在的位置：买卖IC网 > PDF目录15438 > ADM708ARM (Analog Devices Inc)IC SUPERVISOR MPU 4.4V WD 8-MSOP PDF资料下载
参数资料
| 型号： | ADM708ARM |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU 4.4V WD 8-MSOP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 160 ms |
| 电压 - 阀值： | 4.4V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
ADM705/ADM706/ADM707/ADM708
CIRCUIT INFORMATION
POWER-FAIL RESET OUTPUT
RESET is an active low output that provides a reset signal to
the microprocessor whenever the V CC input is below the reset
threshold. An internal timer holds RESET low for 200 ms after
the voltage on V CC rises above the threshold. This functions as a
power-on reset signal for the microprocessor. It allows time for
both the power supply and the microprocessor to stabilize after
When V CC falls below the reset threshold, WDO is forced low
whether or not the watchdog timer has timed out. Normally, this
generates an interrupt, but it is overridden by RESET going low.
The watchdog monitor can be deactivated by floating the
watchdog input (WDI). The WDO can then be used as a low
line output, because it goes low only when V CC falls below the
reset threshold.
power-up. The RESET output is guaranteed to remain valid
t WP
t WD
t WD
t WD
(low) with V CC as low as 1 V. This ensures that the micropro-
cessor is held in a stable shutdown condition as the power
supply voltage ramps up.
In addition to RESET, an active high RESET output is also
WDI
WDO
available on the ADM707/ADM708. This is the complement
of RESET and is useful for processors requiring an active high
RESET
RESET EXTERNALLY
TRIGGERED BY MR
t RS
reset signal.
MANUAL RESET
The manual reset input (MR) allows other reset sources, such
as a manual reset switch, to generate a processor reset. The
input is effectively debounced by the timeout period (200 ms
typical). The MR input is TTL-/CMOS-compatible, so it can
also be driven by any logic reset output.
Figure 14. Watchdog Timing
POWER-FAIL COMPARATOR
The power-fail comparator is an independent comparator that
can be used to monitor the input power supply. The comparator’s
inverting input is internally connected to a 1.25 V reference
voltage. The noninverting input is available at the PFI input.
This input can be used to monitor the input power supply via
V CC
V RT
V RT
t RS
t RS
a resistive divider network. When the voltage on the PFI input
drops below 1.25 V, the comparator output (PFO) goes low,
indicating a power failure. For early warning of power failure,
RESET
the comparator can be used to monitor the preregulator input
simply by choosing an appropriate resistive divider network.
MR
MR EXTERNALLY
The PFO output can be used to interrupt the processor so that
WDO
DRIVEN LOW
a shutdown procedure is implemented before power is lost.
INPUT
POWER
Figure 13. RESET, MR, and WDO Timing
R1
1.25V
PFO
POWER-FAIL
OUTPUT
WATCHDOG TIMER (ADM705/ADM706)
R2
POWER-FAIL
INPUT
PFI
ADM705/ADM706/
The watchdog timer circuit can be used to monitor the activity of
the microprocessor to check that it is not stalled in an indefinite
loop. An output line on the processor is used to toggle the watch-
dog input (WDI) line. If this line is not toggled within the timeout
period (1.60 sec), then the watchdog output (WDO) goes low.
The WDO can be connected to a nonmaskable interrupt (NMI)
on the processor; therefore, if the watchdog timer times out, an
interrupt is generated. The interrupt service routine should then
be used to rectify the problem.
If a RESET signal is required when a timeout occurs, the WDO
should be connected to the manual reset input (MR).
The watchdog timer is cleared by either a high-to-low or a low-
to-high transition on WDI. It is also cleared by RESET going
low; therefore, the watchdog timeout period begins after RESET
goes high.
Rev. G | Page 8 of 12
ADM707/ADM708
Figure 15. Power-Fail Comparator
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21X-EY-F3 | CONVERTER MOD DC/DC 5.2V 50W |
| VI-21X-EY-F2 | CONVERTER MOD DC/DC 5.2V 50W |
| ESM15DTMI-S189 | CONN EDGECARD 30POS R/A .156 SLD |
| ADM706AN | IC SUPERVISOR MPU 4.40V WD 8DIP |
| ADM1232ARW-REEL7 | IC SUPERVISOR FOR CPU 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM708ARM-REEL | 制造商:Analog Devices 功能描述:Processor Supervisor 4.4V 4.4V 8-Pin MSOP T/R 制造商:Analog Devices 功能描述:PROCESSOR SUPERVISOR 4.4V 250UA 8MSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:RESET GENERATOR I.C. - Tape and Reel |
| ADM708ARMZ | 功能描述:IC SUPERVISOR MPU 4.4V WD 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM708ARMZ-REEL | 功能描述:IC SUPERVISOR MPU 4.4V WD 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM708AR-REEL | 功能描述:IC SUPERVISOR MPU 4.4V WD 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| ADM708ARZ | 功能描述:IC SUPERVISOR MPU 4.4 WD 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6717 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:2 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:1.11V，3.075V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 产品目录页面:1194 (CN2011-ZH PDF) 其它名称:497-7019-6 |
发布紧急采购，3分钟左右您将得到回复。