参数资料
型号: ADM802LARN
厂商: Analog Devices Inc
文件页数: 7/8页
文件大小: 0K
描述: IC SUPERVISOR MPU 4.65V WD 8SOIC
标准包装: 98
类型: 备用电池电路
监视电压数目: 1
输出: 推挽式,图腾柱
复位: 低有效
复位超时: 最小为 140 ms
电压 - 阀值: 4.65V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 管件
ADM690A/ADM692A/ADM802L/M/ADM805L/M
If the watchdog timer is not needed, the WDI input should be
left floating.
The Power Fail Input, PFI, monitors the input power supply via
a resistive divider network. The voltage on the PFI input is
compared with a precision 1.25 V internal reference. If the input
voltage drops below 1.25 V, a power fail output ( PFO ) signal is
generated. This warns of an impending power failure and may
be used to interrupt the processor so that the system may be
shut down in an orderly fashion. The resistors in the sensing
network are ratioed to give the desired power fail threshold
voltage V T .
V T = (1.25 R 1/ R 2) + 1.25 V
R 1/ R 2 = ( V T /1.25) – 1
Alternate Watchdog Input Drive Circuits
The watchdog feature can be enabled and disabled under
program control by driving WDI with a 3-state buffer. When
three-stated, the WDI input will float thereby disabling the
watchdog timer.
Operation Without a Backup Supply
If a backup power source is not used, V BATT should be con-
nected to GND and V OUT should be connected to V CC .
Replacing the Backup Battery
The backup battery may be replaced without any danger of
spurious resetting when V CC is present. Since V CC is above the
reset threshold, a reset will not occur even if V BATT is floating
while a replacement battery is being inserted. This differs from
older generation products where leakage currents flowing out
V BATT could cause spurious resetting during battery replacement.
Ps With Bidirectional RESET
In order to prevent contention for microprocessors with a
bidirectional reset line, a current limiting resistor should be
inserted between the ADM69xA/ADM80xx RESET output pin
and the μ P reset pin. This will limit the current to a safe level if
there are conflicting output reset levels. A suitable resistor value
is 4.7 k ? . If the reset output is required for other uses, then it
should be buffered as shown in Figure 13.
High Capacity Backup Capacitors
High capacity (0.1 μ F or greater) capacitors may be used as a
backup power source. A typical application is shown in Fig-
ure 12.
+5V
+5V
V CC
ADM690A
ADM692A
ADM802L
ADM802M
BUFFERED
RESET
μP
V CC
V BATT
V OUT
RESET
RESET *
TO STATIC RAM
TO μP
RESET
GND
RESET
GND
0.1F
+
GND
Figure 13. Bidirectional Reset
* FOR ADM805L/ADM805M ONLY
Figure 12. High Capacity Capacitor
REV. 0
–7 –
相关PDF资料
PDF描述
VE-22Y-EW-B1 CONVERTER MOD DC/DC 3.3V 66W
VI-JWT-EY-F1 CONVERTER MOD DC/DC 6.5V 50W
VE-22X-EY-B1 CONVERTER MOD DC/DC 5.2V 50W
H2BXT-10112-S4-ND JUMPER-H1500TR/A2015S/X 12"
VE-220-EY-B1 CONVERTER MOD DC/DC 5V 50W
相关代理商/技术参数
参数描述
ADM802LARN-REEL 制造商:Analog Devices 功能描述:Processor Supervisor 4.65V 4.65V 8-Pin SOIC N T/R 制造商:Analog Devices 功能描述:PROCESSOR SUPERVISOR 4.65V 100UA 8SOIC N - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:5V CMOS UP I.C. - Tape and Reel
ADM802LARNZ 功能描述:IC SUPERVISOR MPU 4.65V WD 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP(0.059",1.50mm 宽)5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT
ADM802LARNZ-REEL 功能描述:IC SUPERVISOR MPU 4.65V WD 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP(0.059",1.50mm 宽)5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT
ADM802M 制造商:AD 制造商全称:Analog Devices 功能描述:Microprocessor Supervisory Circuits
ADM802MAN 制造商:Analog Devices 功能描述:Processor Supervisor 4.4V 4.4V 8-Pin PDIP 制造商:Analog Devices 功能描述:PROCESSOR SUPERVISOR 4.4V 100UA 8PDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:5V CMOS UP I.C. - Bulk