- 您现在的位置：买卖IC网 > PDF目录20052 > ADN2873ACPZ-RL (Analog Devices Inc)IC LASER DRIVER 4.25GBPS 24LFCSP PDF资料下载
参数资料
| 型号： | ADN2873ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC LASER DRIVER 4.25GBPS 24LFCSP |
| 标准包装： | 5,000 |
| 类型： | 激光二极管驱动器（光纤） |
| 数据速率： | 4.25Gbps |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 31mA |
| 电流 - 调制： | 90mA |
| 电流 - 偏置： | 100mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 24-LFCSP-VQ（4x4） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
ADN2873
RESISTOR SETPOINT CALIBRATION
In resistor setpoint calibration, the PAVREF, ERREF, and RPAV
pins must all be tied to VCC. The average power and extinction
ratio can be set using the PAVSET and ERSET pins, respectively.
A resistor is placed between the pin and GND to set the current
flowing in each pin, as shown in Figure 30. The ADN2873
ensures that both PAVSET and ERSET are kept 1.23 V above
GND. The PAVSET and ERSET resistors are given by
Method 2: Measuring I MPD Across a Sense Resistor
The second method has the advantage of providing a valid I MPD
reading at all times but has the disadvantage of requiring a
differential measurement across a sense resistor directly in
series with the I MPD . As shown in Figure 32, a small resistor, Rx,
is placed in series with the I MPD . If the laser used in the design
has a pinout where the monitor photodiode cathode and the
lasers anode are not connected, a sense resistor, Rx, can be placed
R PAVSET =
R ERSET =
1 . 2 V
P AV × R SP
1 .2 V × 100
I MOD
where:
P AV is the average power required (mW). R SP is the optical
responsivity (in mA/mW).
I MOD is the modulation current required (mA).
Power-On Sequence in Resistor Setpoint Mode
(kΩ)
(kΩ)
in series with the photodiode cathode and V CC , as shown in
take into account the expected I MPD value in normal operation.
The resistor must be large enough to make a significant signal
for the buffered ADC to read, but small enough not to cause a
significant voltage reduction across the photodiode. The voltage
across the sense resistor should not exceed 250 mV when the
laser is in normal operation. It is recommended that a 10 pF
capacitor be placed in parallel with the sense resistor.
V CC
Note that during power-up, the ADN2873 starts an initial process
sequence that allows 25 ms before enabling the device alarms.
The resistors connected to the PAVSET and ERSET pins should
PHOTODIODE
LD
be stable within 20 ms after turning on the power supply. The
ADN2873 alarm may kick in and assert FAIL, provided the
MICROCONVERTER
ADC DIFFERENTIAL
INPUT
200 ?
Rx
10pF
PAVSET and ERSET resistors are stabilized 20 ms after turning
on the power supply.
I MPD MONITORING
I MPD monitoring can be implemented for voltage setpoint and
resistor setpoint as described in the following sections.
PAVSET
ADN2873
Figure 32. Differential Measurement of I MPD Across a Sense Resistor
V CC V CC
Voltage Setpoint
In voltage setpoint calibration, two methods can be used for
I MPD monitoring: measuring voltage at RPAV and measuring
MICROCONVERTER
ADC
INPUT
200 ?
Rx
LD
I MPD across a sense resistor.
Method 1: Measuring Voltage at RPAV
The I MPD current is equal to the voltage at RPAV divided by the
value of RPAV (see Figure 31) as long as the laser is on and is
being controlled by the control loop. This method does not
provide a valid I MPD reading when the laser is in shutdown or fail
mode. A microconverter-buffered ADC input can be connected to
RPAV to make this measurement. No decoupling or filter capaci-
tors should be placed on the RPAV node because this can disturb
the control loop.
V CC
PHOTODIODE
PAVSET
ADN2873
PHOTODIODE
PAVSET
ADN2873
Figure 33. Single Measurement of I MPD Across a Sense Resistor
Resistor Setpoint
In resistor setpoint calibration, the current through the resistor
from PAVSET to GND is the I MPD current. The recommended
method for measuring the I MPD current is to place a small resis-
tor in series with the PAVSET resistor (or potentiometer) and
measure the voltage across this resistor, as shown in Figure 34. The
I MPD current is then equal to this voltage divided by the value of
resistor used. In resistor setpoint calibration, PAVSET is held to
1.2 V nominal; it is recommended that the sense resistor be
selected so that the voltage across the sense resistor does not
MICROCONVERTER
ADC
INPUT
RPAV
exceed 250 mV.
R
1k ?
Figure 31. Single Measurement of I MPD at RPAV in Voltage Setpoint Mode
Rev. 0 | Page 15 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| EEM08DRKF-S13 | CONN EDGECARD 16POS .156 EXTEND |
| RMA32DTMD | CONN EDGECARD 64POS R/A .125 SLD |
| HMK316B7224ML-T | CAP CER 0.22UF 100V 20% X7R 1206 |
| ABB25DHAN | CONN EDGECARD 50POS R/A .050 SLD |
| GRM1885C1H7R5DZ01D | CAP CER 7.5PF 50V NP0 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN2873ACPZ-RL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:3.3 V, 50 Mbps to 4.25 Gbps, Single-Loop, Laser Diode Driver |
| ADN2873XCPZ | 功能描述:IC LASER DRIVER CSP 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADN2880 | 制造商:AD 制造商全称:Analog Devices 功能描述:3.2 Gbps, 3.3 V, Low Noise, Transimpedance Amplifier |
| ADN2880ACHIPS | 制造商:Analog Devices 功能描述:3.2 GBPS 3.3V LOW NOISE TIA |
| ADN2882 | 制造商:AD 制造商全称:Analog Devices 功能描述:4.25 Gbps 3.3V Low Noise Transimpedance Amplifier |
发布紧急采购，3分钟左右您将得到回复。