- 您现在的位置：买卖IC网 > PDF目录165352 > ADP1111AN (ANALOG DEVICES INC) Micropower, Step-Up/Step-Down SW Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V PDF资料下载
参数资料
| 型号： | ADP1111AN |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 稳压器 |
| 英文描述： | Micropower, Step-Up/Step-Down SW Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 88 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封装： | PLASTIC, DIP-8 |
| 文件页数： | 2/16页 |
| 文件大小： | 408K |
| 代理商： | ADP1111AN |
ADP1111
–10–
REV. 0
CIRCUIT OPERATION, STEP DOWN (BUCK) MODE)
The ADP1111’s step down mode is used to produce an output
voltage that is lower than the input voltage. For example, the
output of four NiCd cells (+4.8 V) can be converted to a +3 V
logic supply.
A typical configuration for step down operation of the ADP1111
is shown in Figure 19. In this case, the collector of the internal
power switch is connected to VIN and the emitter drives the
inductor. When the switch turns on, SW2 is pulled up towards
VIN. This forces a voltage across L1 equal to VIN – VCE – VOUT
and causes current to flow in L1. This current reaches a final
value of:
IPEAK
VIN VCE VOUT
L
7s
where 7
s is the ADP1111 switch’s “on” time.
ILIM VIN SW1
SW2 4
GND
SET
AO
ADP1111
NC
L1
D1
1N5818
RLIM
100
1
+
VIN
2
3
6
7
5
NC
C2
+
VOUT
R2
R1
CL
FB 8
Figure 19. Step-Down Mode Operation
When the switch turns off, the magnetic field collapses. The
polarity across the inductor changes, and the switch side of the
inductor is driven below ground. Schottky diode D1 then turns
on, and current flows into the load. Notice that the Absolute
Maximum Rating for the ADP1111’s SW2 pin is 0.5 V below
ground. To avoid exceeding this limit, D1 must be a Schottky
diode. If a silicon diode is used for D1, Pin SW2 can go to
–0.8 V, which will cause potentially damaging power dissipation
within the ADP1111.
The output voltage of the buck regulator is fed back to the
ADP1111’s FB pin by resistors R1 and R2. When the voltage at
pin FB falls below 1.25 V, the internal power switch turns “on”
again, and the cycle repeats. The output voltage is set by the
formula:
VOUT = 1.25 V 1 +
R2
R1
When operating the ADP1111 in step-down mode, the output
voltage is impressed across the internal power switch’s emitter-
base junction when the switch is off. To protect the switch, the
output voltage should be limited to 6.2 V or less. If a higher
output voltage is required, a Schottky diode should be placed in
series with SW2 as shown in Figure 20.
ILIM VIN SW1
SW2
FB
GND
ADP1111
L1
D1
R3
1
+
VIN
2
3
5
8
4
C2
+
VOUT
R2
R1
D2
C1
D1, D2 = 1N5818 SCHOTTKY DIODES
Figure 20. Step-Down Model, VOUT > 6.2 V
If the input voltage to the ADP1111 varies over a wide range, a
current limiting resistor at Pin 1 may be required. If a particular
circuit requires high peak inductor current with minimum input
supply voltage, the peak current may exceed the switch maxi-
mum rating and/or saturate the inductor when the supply
voltage is at the maximum value. See the “Limiting the Switch
Current” section of this data sheet for specific recommendations.
INCREASING OUTPUT CURRENT IN THE STEP-DOWN
REGULATOR
Unlike the boost configuration, the ADP1111’s internal power
switch is not saturated when operating in step-down mode. A
conservative value for the voltage across the switch in step-down
mode is 1.5 V. This results in high power dissipation within the
ADP1111 when high peak current is required. To increase the
output current, an external PNP switch can be added (Figure
21). In this circuit, the ADP1111 provides base drive to Q1
through R3, while R4 ensures that Q1 turns off rapidly. Because
the ADP1111’s internal current limiting function will not work
in this circuit, R5 is provided for this purpose. With the value
shown, R5 limits current to 2 A. In addition to reducing power
dissipation on the ADP1111, this circuit also reduces the switch
voltage. When selecting an inductor value for the circuit of
Figure 21, the switch voltage can be calculated from the
formula:
V
= V
+ V
0.6 V + 0.4 V
1 V
SW
R5
Q1(SAT)
ILIM
VIN
SW1
SW2
FB
GND
SET
AO
ADP1111
NC
L1
D1
1N5821
R5
0.3
1
INPUT
2
3
6
7
5
4
8
NC
CINPUT
+
R1
R2
CL
+
OUTPUT
R3
330
R4
220
Q1
MJE210
Figure 21. High Current Step-Down Operation
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1650ACBZ-R7 | LED DISPLAY DRIVER, PBGA12 |
| ADP1650ACPZ-R7 | LED DISPLAY DRIVER, PDSO10 |
| ADP3157 | 5-Bit Programmable Synchronous Controller for Pentium III Processors |
| ADP3159 | 4-Bit Programmable Synchronous Buck Controllers |
| ADP3162 | 5-Bit Programmable 2-Phase Synchronous Buck Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1111AN-12 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin PDIP N 制造商:Rochester Electronics LLC 功能描述:MICROPOWER STEP-UP/DOWN SWITCHING REG. - Bulk |
| ADP1111AN-3.3 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin PDIP N 制造商:Rochester Electronics LLC 功能描述:MICROPOWER STEP-UP/DOWN SWITCHING REG. - Bulk |
| ADP1111AN-33 | 制造商:AD 制造商全称:Analog Devices 功能描述:Micropower, Step-Up/Step-Down SW Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
| ADP1111AN-5 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin PDIP N 制造商:Rochester Electronics LLC 功能描述:MICROPOWER STEP-UP/DOWN SWITCHING REG. - Bulk |
| ADP1111ANZ | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin PDIP 制造商:Analog Devices 功能描述:IC V REG STEP UP/DOWN ADJ PDIP8 |
发布紧急采购，3分钟左右您将得到回复。