- 您现在的位置：买卖IC网 > PDF目录1776 > ADP130AUJZ-2.5-R7 (Analog Devices Inc)IC REG LDO 2.5V .35A TSOT-23-5 PDF资料下载
参数资料
| 型号： | ADP130AUJZ-2.5-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.5V .35A TSOT-23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.5V |
| 输入电压： | 最高 3.6V |
| 电压 - 压降（标准）： | 0.07V @ 350mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 350mA（最小值） |
| 电流 - 限制（最小）： | 400mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 792 (CN2011-ZH PDF) |
| 配用： | ADP130-2.5-EVALZ-ND - BOARD EVAL FOR ADP130 2.5V |
| 其它名称： | ADP130AUJZ-2.5-R7DKR |
Data Sheet
CURRENT LIMIT AND THERMAL OVERLOAD
PROTECTION
The ADP130 is protected against damage due to excessive power
dissipation by current limit and thermal overload protection
circuits. The ADP130 is designed to current limit when the
output load reaches 550 mA (typical). When the output load
ADP130
the junction and ambient air (θ JA ). The value of θ JA is dependent on
the package assembly compounds used and the amount of copper
to which the GND pins of the package are soldered on the PCB.
various PCB copper sizes.
Table 6. Typical θ JA Values for Specified PCB Copper Sizes
exceeds 550 mA, the output voltage is reduced to maintain
a constant current limit.
Thermal overload protection limits the junction temperature to
a maximum of 150°C typical. Under extreme conditions (that is,
high ambient temperature and power dissipation) when the
junction temperature starts to rise above 150°C, the output is
Copper Size (mm 2 )
0 1
50
100
300
500
θ JA (°C/W)
170
152
146
134
131
turned off, reducing output current to zero. When the junction
temperature drops below 135°C, the output is turned on again and
1
Device soldered to minimum size pin traces.
output current is restored to its nominal value.
Consider the case where a hard short from VOUT to GND occurs.
The junction temperature of the ADP130 can be calculated from
the following equation:
At first, the ADP130 current limits so that only 550 mA is con-
ducted into the short. If self-heating of the junction is great enough
to cause its temperature to rise above 150°C, thermal shutdown
activates, turning off the output and reducing the output current to
zero. As the junction temperature cools and drops below 135°C,
the output turns on and conducts 550 mA into the short, again
T J = T A + ( P D × θ JA )
where:
T A is the ambient temperature.
P D is the power dissipation in the die, given by
P D = [( V IN ? V OUT ) × I LOAD ] + ( V IN × I GND )
(2)
(3)
causing the junction temperature to rise above 150°C. This
thermal oscillation between 135°C and 150°C causes a current
oscillation between 550 mA and 0 mA that continues as long
as the short remains at the output.
Current limit and thermal overload protections protect the device
against accidental overload conditions. For reliable operation,
device power dissipation must be externally limited so that
where:
V IN and V OUT are the input and output voltages, respectively.
I LOAD is the load current.
I GND is the ground current.
Power dissipation due to ground current is quite small and can
be ignored. Therefore, the junction temperature equation can
be simplified as follows:
junction temperatures do not exceed 125°C.
T J = T A + {[( V IN ? V OUT ) × I LOAD ] × θ JA }
(4)
THERMAL CONSIDERATIONS
To guarantee reliable operation, the junction temperature of the
ADP130 must not exceed 125°C. To ensure that the junction tem-
perature stays below this maximum value, the user needs to be
aware of the parameters that contribute to junction temperature
changes. These parameters include ambient temperature, power
dissipation in the power device, and thermal resistances between
As shown in Equation 4, for a given ambient temperature, input-
to-output voltage differential, and continuous load current,
a minimum copper size requirement exists for the PCB to ensure
through Figure 46 show junction temperature calculations for
different ambient temperatures, load currents, V IN to V OUT
differentials, and areas of PCB copper.
Rev. C | Page 15 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| ADP150AUJZ-2.5-R7 | IC REG LDO 2.5V .15A TSOT-5 |
| ADP151ACPZ-3.0-R7 | IC REG LDO 3V .2A 6LFCSP |
| ADP160AUJZ-1.5-R7 | IC REG LDO 1.5V .15A 5TSOT |
| ADP1610ARMZ-R7 | IC REG BOOST ADJ 1.2A 8MSOP |
| ADP1611ARMZ-R7 | IC REG BOOST ADJ 1.2A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP130-BL1-EVZ | 制造商:Analog Devices 功能描述:BLANK ADISIMPOWER EVAL ADP130 - Boxed Product (Development Kits) |
| ADP130UJZ-REDYKIT | 功能描述:KIT REDI TOOL 1.2/1.8 ADP130 RoHS:是 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:Redykit™ 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ADP150 | 制造商:AD 制造商全称:Analog Devices 功能描述:Ultralow Noise, 150 mA CMOS Linear Regulator |
| ADP150_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:Ultralow Noise, 150 mA CMOS Linear Regulator |
| ADP150_VA | 制造商:AD 制造商全称:Analog Devices 功能描述:Ultralow Noise, 150 mA CMOS Linear Regulator |
发布紧急采购，3分钟左右您将得到回复。