- 您现在的位置：买卖IC网 > PDF目录13141 > ADP151AUJZ-2.8-R7 (Analog Devices Inc)IC REG LDO 2.8V .2A 5TSOT PDF资料下载
参数资料
| 型号： | ADP151AUJZ-2.8-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/24页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.8V .2A 5TSOT |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.8V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.15V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA（最小值） |
| 电流 - 限制（最小）： | 220mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | ADP151AUJZ-2.8-R7DKR |
ADP151
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Output Capacitor
The ADP151 is designed for operation with small, space-saving
ceramic capacitors but can function with most commonly used
capacitors as long as care is taken with regard to the effective
series resistance (ESR) value. The ESR of the output capacitor
affects the stability of the LDO control loop. A minimum of 1 μF
capacitance with an ESR of 1 ? or less is recommended to ensure
the stability of the ADP151. Transient response to changes in load
current is also affected by output capacitance. Using a larger value
of output capacitance improves the transient response of the
ADP151 to large changes in load current. Figure 28 shows the
transient responses for an output capacitance value of 1 μF.
T
LOAD CURRENT
1
Data Sheet
of an 0402, 1 μF, 10 V X5R capacitor. The voltage stability of a
capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or higher voltage
rating exhibits better stability. The temperature variation of the
X5R dielectric is ~±15% over the ?40°C to +85°C temperature
range and is not a function of package or voltage rating.
1.2
1.0
0.8
0.6
0.4
0.2
0
0
2
4
6
8
10
VOLTAGE BIAS
2
V OUT
Figure 29. Capacitance vs. Voltage Bias Characteristic
Use Equation 1 to determine the worst-case capacitance, accounting
for capacitor variation over temperature, component tolerance,
and voltage.
CH1 200mA
CH2 50mV
M20μs
A CH1
64mA
C EFF = C BIAS × (1 ? TEMPCO ) × (1 ? TOL )
(1)
T 10.00%
Figure 28. Output Transient Response, C OUT = 1 μF
Input Bypass Capacitor
Connecting a 1 μF capacitor from VIN to GND reduces
the circuit sensitivity to the printed circuit board (PCB) layout,
especially when long input traces or high source impedance
are encountered. If greater than 1 μF of output capacitance is
required, the input capacitor should be increased to match it.
Input and Output Capacitor Properties
Any good quality ceramic capacitor can be used with the
ADP151, as long as it meets the minimum capacitance and
maximum ESR requirements. Ceramic capacitors are manufac-
tured with a variety of dielectrics, each with different behavior
over temperature and applied voltage. Capacitors must have an
adequate dielectric to ensure the minimum capacitance over the
necessary temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recommended.
where:
C BIAS is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient (TEMPCO)
over ?40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
Substituting these values in Equation 1 yields
C EFF = 0.94 μF × (1 ? 0.15) × (1 ? 0.1) = 0.719 μF
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over tempera-
ture and tolerance at the chosen output voltage.
To guarantee the performance of the ADP151, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
Y5V and Z5U dielectrics are not recommended, due to their
poor temperature and dc bias characteristics.
Rev. E | Page 12 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| UPM1J680MPD | CAP ALUM 68UF 63V 20% RADIAL |
| ESC25DRTS-S734 | CONN EDGECARD 50POS DIP .100 SLD |
| VI-B6B-EU | CONVERTER MOD DC/DC 95V 200W |
| ECM25DREH | CONN EDGECARD 50POS .156 EYELET |
| VI-B62-EU | CONVERTER MOD DC/DC 15V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP151AUJZ-3.0-R7 | 功能描述:IC REG LDO 3V .2A 5TSOT RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.12V @ 150mA 稳压器数量:1 电流 - 输出:150mA（最小值） 电流 - 限制（最小）:220mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) 其它名称:ADP160AUJZ-3.0-R7TR |
| ADP151AUJZ-3.3-R7 | 功能描述:IC REG LDO 3.3V .2A 5TSOT RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.12V @ 150mA 稳压器数量:1 电流 - 输出:150mA（最小值） 电流 - 限制（最小）:220mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) 其它名称:ADP160AUJZ-3.0-R7TR |
| ADP151CB-3.3-EVALZ | 功能描述:EVAL BOARD FOR ADP151 RoHS:是 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:- 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ADP151CPZ-REDYKIT | 制造商:Analog Devices 功能描述:KIT DEV REDYKIT ADP151CPZ 制造商:Analog Devices 功能描述:ADP151, LDO, CMOS, EVALUATION KIT 制造商:Analog Devices 功能描述:ADP151, LDO, CMOS, EVALUATION KIT; Silicon Manufacturer:Analog Devices; Silicon Core Number:ADP151; Kit Application Type:Power Management - Voltage Regulator; Application Sub Type:LDO; Kit Contents:Board, Manual |
| ADP151UJZ-REDYKIT | 功能描述:KIT REDI TOOL ADP151 RoHS:是 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:Redykit™ 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
发布紧急采购，3分钟左右您将得到回复。