- 您现在的位置：买卖IC网 > PDF目录1776 > ADP1613ARMZ-R7 (Analog Devices Inc)IC REG BOOST SEPIC ADJ 2A 8MSOP PDF资料下载
参数资料
| 型号： | ADP1613ARMZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SEPIC ADJ 2A 8MSOP |
| 设计资源： | Powering a 30V DAC from a 3V supply (CN0193) |
| 标准包装： | 1 |
| 类型： | 升压（升压），Sepic |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 20 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 650kHz，1.3MHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-MSOP |
| 产品目录页面： | 791 (CN2011-ZH PDF) |
| 配用： | ADP1613-12-EVALZ-ND - BOARD EVAL FOR ADP1613 |
| 其它名称： | ADP1613ARMZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
THEORY OF OPERATION
V IN
C IN
>1.6V
L1
ADP1612/ADP1613
VIN
6
<0.3V
7
FREQ
V IN
D
COMPARATOR
+
+
A
CURRENT
5
SW
D1
C OUT
V OUT
V OUT
ERROR
PWM
COMPARATOR
D REF
SENSING
R1
FB
2
AMPLIFIER
OSCILLATOR
R2
V BG
UVLO
5μA
R COMP
COMP
1
V IN
UVLO REF
COMPARATOR
S
R
Q
DRIVER
N1
C COMP
V SS
5μA
T SENSE
TSD
COMPARATOR
SS
8
SOFT
START
T REF
RESET
BG
BAND GAP
C SS
AGND
1.1M?
AGND
ADP1612/AD1613
EN
3
>1.6V
4
GND
<0.3V
Figure 34. Block Diagram with Step-Up Regulator Application Circuit
The ADP1612/ADP1613 current-mode step-up switching
converters boost a 1.8 V to 5.5 V input voltage to an output
voltage as high as 20 V. The internal switch allows a high
output current, and the high 650 kHz/1.3 MHz switching
frequency allows for the use of tiny external components.
The switch current is monitored on a pulse-by-pulse basis to
limit it to 1.4 A typical (ADP1612) or 2.0 A typical (ADP1613).
CURRENT-MODE PWM OPERATION
The ADP1612/ADP1613 utilize a current-mode PWM control
scheme to regulate the output voltage over all load conditions.
The output voltage is monitored at FB through a resistive voltage
divider. The voltage at FB is compared to the internal 1.235 V
reference by the internal transconductance error amplifier to
create an error voltage at COMP. The switch current is internally
measured and added to the stabilizing ramp. The resulting sum
is compared to the error voltage at COMP to control the PWM
modulator. This current-mode regulation system allows fast
transient response, while maintaining a stable output voltage.
By selecting the proper resistor-capacitor network from COMP
to GND, the regulator response is optimized for a wide range of
input voltages, output voltages, and load conditions.
FREQUENCY SELECTION
The frequency of the ADP1612/ADP1613 is pin-selectable
to operate at either 650 kHz to optimize the regulator for high
efficiency or at 1.3 MHz for use with small external components.
If FREQ is left floating, the part defaults to 650 kHz. Connect
FREQ to GND for 650 kHz operation or connect FREQ to VIN
for 1.3 MHz operation. When connected to VIN for 1.3 MHz
operation, an additional 5 μA, typical, of quiescent current is
active. This current is turned off when the part is shutdown.
SOFT START
To prevent input inrush current to the converter when the part is
enabled, connect a capacitor from SS to GND to set the soft start
period. Once the ADP1612/ADP1613 are turned on, SS sources
5 μA, typical, to the soft start capacitor (C SS ) until it reaches
1.2 V at startup. As the soft start capacitor charges, it limits the
peak current allowed by the part. By slowly charging the soft
start capacitor, the input current ramps slowly to prevent it
from overshooting excessively at startup. When the ADP1612/
ADP1613 are in shutdown mode (EN ≤ 0.3 V), a thermal shut-
down event occurs, or the input voltage is below the falling
undervoltage lockout voltage, SS is internally shorted to GND
to discharge the soft start capacitor.
Rev. D | Page 11 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1614ACPZ-650-R7 | IC REG BOOST ADJ 4A 10LFCSP |
| ADP1621ARMZ-R7 | IC REG CTRLR PWM CM 10-MSOP |
| ADP1707ARDZ-1.8-R7 | IC REG LDO 1.8V 1A 8-SOIC |
| ADP170AUJZ-2.5-R7 | IC REG LDO 2.5V .3A TSOT23-5 |
| ADP1711AUJZ-3.0-R7 | IC REG LDO 3V .15A TSOT-23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1613ARMZ-R7 | 制造商:Analog Devices 功能描述:IC STEP-UP DC/DC SWITCHING CONV MSOP-8 |
| ADP1613-BL1-EVZ | 制造商:Analog Devices 功能描述:Evaluation Board Operates In Pulse-Width Modulation Current Mode 制造商:Analog Devices 功能描述:BLANK ADISIMPOWER EVAL ADP1613 - Boxed Product (Development Kits) 制造商:Analog Devices 功能描述:650 kHz/1.3 MHz Step-Up Converter Blank |
| ADP1613-BL2-EVZ | 制造商:Analog Devices 功能描述:BLANK SEPIC DEMO BOARD - Boxed Product (Development Kits) |
| ADP1613-BL3-EVZ | 功能描述:EVAL BLANK ADISIMPOWER ADP1613 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADP1614 | 制造商:AD 制造商全称:Analog Devices 功能描述:650 kHz/1.3 MHz, 4 A, Step-Up |
发布紧急采购，3分钟左右您将得到回复。