- 您现在的位置：买卖IC网 > PDF目录14149 > ADP3050ARZ-3.3-RL (Analog Devices Inc)IC REG BUCK 3.3V 1A 8SOIC PDF资料下载
参数资料
| 型号： | ADP3050ARZ-3.3-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 1A 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 3.6 V ~ 30 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SO |
| 其它名称： | ADP3050ARZ-3.3-RLDKR |
Data Sheet
Dual Output SEPIC Regulator
For many systems, a dual polarity supply is needed. The circuit
in Figure 30 generates both a positive and a negative 5 V output
using a single magnetic component. The two inductors shown
are actually two separate windings on a single core contained in a
small, surface-mount package. The windings can be connected in
parallel or in series to be used as a single inductor for a conven-
tional buck regulator, or they can be used as a 1:1 transformer,
as in this application. The first winding is used as the standard
buck inductor for the +5 V output. The second winding is used
to generate the ?5 V output along with D2, C6, and C7.
ADP3050
connected to produce the ?5 V supply. The ?5 V output is
generated even without C6 in the circuit, but its inclusion
greatly improves the regulation of the negative output and
lowers the inductor ripple current. The total output current
available for both supplies is limited by the ADP3050 (internally
limited to around 1.0 A).
Keeping load currents below 500 mA and 250 mA, for the
positive and negative supplies, respectively, ensures that the
current limit is not reached under normal operation. These
limits are not interchangeable; 500 mA cannot be drawn from
the ?5 V supply while drawing only 250 mA from the +5 V
D1
1N5818
C3
L1*
25μH
D3
1N4148
L1*
25μH
+
C6 D2
100μF 1N5818
1 SWITCH IN 8
+ C7
100μF
–5V AT 0.25A
V OUT
+5V AT 0.5A
V OUT
+ C5
100μF
supply. The maximum current available from the ?5 V output is
directly related to the +5 V load current, due to the fact that the
+5 V output is used to regulate both supplies. Typically, the ?5 V
load current should be around one-half of the +5 V load current
to ensure good regulation of both outputs. Additionally, the ?5 V
output should have a preload (the minimum current level) of
1% to 2% of the +5 V load current. This helps maintain good
regulation of the ?5 V output at light loads.
0.22μF
2 BOOST
3 BIAS
GND 7
SD 6
The ripple voltage of the +5 V output is that of a normal buck
regulator as described in the Applications Information section.
This ripple voltage is determined by the inductor ripple current
*INDUCTOR IS A SINGLE CORE
WITH TWO WINDINGS
COILTRONICS CTX25-4
SD
12V
V IN
+ C1
22μF
GND
4 FB COMP 5
U1
ADP3050-5
C2
0.01μF
R1
5.1k?
C4
1nF
and the ESR of the output capacitor. For Figure 30, the positive
output voltage ripple is a 30 mV peak-to-peak triangular wave.
The ripple voltage of the ?5 V output is a rectangular wave, due
to the rectangular shape of the current waveform into the ?5 V
output capacitor. The amplitude of this current waveform is
approximately equal to twice the ?5 V load current. For a load
current of 200 mA and an ESR of 100 mΩ, the negative output
voltage ripple is approximately 2 × 200 mA × 100 mΩ, or about
Figure 30. Dual Output +5 V and ?5 V Regulator
These components form a single-ended primary inductance
converter (SEPIC) using the 1:1 coupled inductor to generate
the negative supply. When the switch is off, the voltage across
the buck winding is equal to V O + V D (V D is the diode drop).
This voltage is generated across the second winding, which is
40 mV. The edges of this ripple waveform are quite fast. Along
with the inductance of the output capacitor, it generates narrow
spikes on the negative output voltage. These spikes can easily be
filtered out using an additional 5 μF to 10 μF bypass capacitor
close to the load (the inductance of the PCB trace and the
additional capacitor create a low-pass filter to remove these
high frequency spikes).
Rev. C | Page 19 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| RMM15DTKD-S288 | CONN EDGECARD 30POS .156 EXTEND |
| VE-BNK-EW-F2 | CONVERTER MOD DC/DC 40V 100W |
| ADP3050ARZ-RL | IC REG BUCK ADJ 1A 8SOIC |
| HM78-50150LFTR | SHIELDED INDUCTORS |
| MAX6867UK20D5S+T | IC MPU SUPERVISOR SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP3050ARZ-5 | 功能描述:IC REG BUCK 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| ADP3050ARZ-5-REEL | 功能描述:IC REG BUCK 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| ADP3050ARZ-5-REEL7 | 功能描述:IC REG BUCK 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| ADP3050ARZ-R7 | 功能描述:IC REG BUCK ADJ 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| ADP3050ARZ-RL | 功能描述:IC REG BUCK ADJ 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。